background image

General Specifications

This is a list of specification parameters for the EDS model "A" with calibration schedule "D".  These specifications are operational and
performance standards (or limits) against which the EDS was tested or calculated.  Specifications are subject to change without notice.

Operating Voltage & Current @ 25° C. @ 25% RH. (measured from mean, in "D" & "N" mode)
Min:

6.75 VDC @ 2.55 ma. idle (2.95 ma. mean with typ operation)

Nom:

8.00 VDC @ 3.75 ma. idle (4.15 ma. mean with typ operation)

Max:

15.0 VDC @ 5.10 ma. idle (5.65 ma. mean with typ operation)

Reverse voltage protection
Diode shunt (  3 amp max @ 750 mv., no internal fuse or overvoltage regulator is provided)

Battery test fault voltage point (measured from mean)
Nom:

6.25 VDC @ 25° C. @ 25% RH @ 140 ma. during battery test

Battery Life (measured from mean, assuming fresh alkaline battery operating under typical operating conditions)
Nom:

40 Hrs @ 25° C. @ 25% RH

Valve life:

200 million cycles Min. @ 25 psig. @ 25° C.

Operating Temperature and Humidity (assumes nominal operating voltage)
Min:

0% RH @ -55° C to +80° C.

Nom:

25% RH @ +25° C.

Max:

100% RH @ +50° C. near condensing

Vibration
Random vibration 5 to 500 Hz, 15 minutes per axis @ 2.5 g. (rms) sin wave

Operating pressure range (pressure altitude)
Min:

3.4 psia. @ 25° C. (appx 30,000 ft.)

Max:

20.0 psia. @ 25° C. (appx. -1,000 ft.)

Responsive:

13.70 to 2.70 psia. @ 25° C. (Operational responsive pressure curve range)

Accuracy (sum of pressure hysterisis and linearity through full span)
+- 2.5%  @ 13.70 to 4.7 psia. @ 25° C.
+- 2.5% temperature effect (from 0° C. to 50° C. @ 25% RH) on accuracy and offset

Repeatability (for absolute pressure hysterisis and linearity)
+- 2.5% through full span of 13.70 to 4.7 psia. @ 25° C. @ 25% RH

"D" mode accuracy and hysterisis (measured from mean, with standard calibration)
Acc:

+- 0.250 psia. (  +- 500 ft.) @ 25° C. @ 25% RH.

Hys:

+- 0.550 psia. (  +- 1,400 ft.) @ 25° C. @ 25% RH.

Physical characteristics (EDS unit only)
Width:

3.250" (82.55 mm.)

Height:

5.650" (143.51 mm.)

Depth A:

1.525" (38.73 mm.) main body.

Depth B:

1.900" (48.26 mm.) with switch protector and 3M® Dual Lock

Weight:

14.0 Oz. (0.374 kg.) Full Dress with battery

Height

Width

Depth

Front view

Top view

Switch 
Protector

 100 mm.

A B

Typical operating characteristic is   15 
Resp/min. for a duration of one hour @ 
15,000 ft. @ 25° C. @ 25% RH.

External voltage must have less than 50 
mv. p.p ripple from 0.025 Hz. to 2.5 KHz.

Summary of Contents for EDS A-1












Reviews: