MGE UPS Systems 66102 Page 31 User Manual Download

Page: 31 / 63

T H E U N I N T E R R U P T I B L E P O W E R P R O V I D E R

Network Management Card – User Manual

34003991EN/GA

- 31 -

4.4.1 Network settings

Click on "

Network

" in the menu.

This menu enables the administrator to configure the network parameters of the card and authorisation of the remote upgrade of the

embedded system.

IP Address

: The IP address of the card (e.g.: 172.17.22.252).

Subnet Mask

: The mask of the sub-network of your network (e.g.: 255.255.255.0).

Gateway Address

: Indicate the IP address of the gateway to access the stations located outside the card’s subnet (e.g.: 172.17.17.1).

Hostname

must be suited to the card. This is the first part of the fully qualified domain name, used by the DNS.

As the card does not support NetBIOS protocol, the hostname will only be sent to DNS if the DHCP server sends it the hostname with

the new IP address. This mechanism is described in the update of the DNS protocol RFC 2136

Domain Name

is the domain to which the card belongs. This is the part of the fully qualified domain name that follows the hostname and

is used by the DNS. The default value of the two parameters comprising the fully qualified domain name: ups.domain.com

BOOTP/DHCP

: Authorises (choose "Enabled") configuration of network parameters with your BootP/DHCP server when the card is

booted.

Mode of card operation with server: After each startup, the card makes 5 attempts to recover the network parameters. If no response is

Downloaded from

Elcodis.com

electronic components distributor

Summary of Contents for 66102
































































Search results

Summary of Contents for 66102

Reviews:

Related manuals for 66102

Brands by name

Popular brands

MGE UPS Systems 66102, User Manual

Search results

Summary of Contents for 66102

Reviews:

Related manuals for 66102

Brands by name

Popular brands