background image

 

 

FULL 12-MONTH WARRANTY 

 

MFJ Enterprises, Inc. warrants to the original owner of this product, if manufactured by MFJ Enterprises, 
Inc. and purchased from an authorized dealer or directly from MFJ Enterprises, Inc. to be free from 
defects in material and workmanship for a period of 12 months from date of purchase provided the 
following terms of this warranty are satisfied. 

 

1.

  The purchaser must retain the dated proof-of-purchase (bill of sale, canceled check, credit 

card or money order receipt, etc.) describing the product to establish the validity of the warranty 
claim and submit the original or machine reproduction of such proof of purchase to MFJ 
Enterprises, Inc. at the time of warranty service. MFJ Enterprises, Inc. shall have the discretion to 
deny warranty without dated proof-of-purchase. Any evidence of alteration, erasure, of forgery 
shall be cause to void any and all warranty terms immediately. 

 

2.

  MFJ Enterprises, Inc. agrees to repair or replace at MFJ's option without charge to the 

original owner any defective product provided the product is returned postage prepaid to MFJ 
Enterprises, Inc. with a personal check, cashiers check, or money order for 

$12.00 

covering 

postage and handling. 

 

3.

  MFJ Enterprises, Inc. will supply replacement parts free of charge for any MFJ product under 

warranty upon request. A dated proof of purchase and a

 $8.00

 personal check, cashiers check, or 

money order must be provided to cover postage and handling. 

 

4.

  This warranty is 

NOT

 void for owners who attempt to repair defective units. Technical 

consultation is available by calling (662) 323-5869. 

 

5.

  This warranty does not apply to kits sold by or manufactured by MFJ Enterprises, Inc. 

 

5.

  Wired and tested PC board products are covered by this warranty provided 

only the wired 

and tested PC board product is returned.

 Wired and tested PC boards installed in the owner's 

cabinet or connected to switches, jacks, or cables, etc. sent to MFJ Enterprises, Inc. will be 
returned at the owner's expense un-repaired. 

 

6.

   Under no circumstances is MFJ Enterprises, Inc. liable for consequential damages to person 

or property by the use of any MFJ products. 

 

8.

 

Out-of-Warranty Service: 

MFJ Enterprises, Inc. will repair any out-of-warranty product 

provided the unit is shipped prepaid. All repaired units will be shipped COD to the owner. Repair 
charges will be added to the COD fee unless other arrangements are made. 

 

9.

  This warranty is given in lieu of any other warranty expressed or implied. 

 

10.

  MFJ Enterprises, Inc. reserves the right to make changes or improvements in design or 

manufacture without incurring any obligation to install such changes upon any of the products 
previously manufactured. 

 

11.

  All MFJ products to be serviced in-warranty or out-of-warranty should be addressed to 

MFJ 

Enterprises, Inc., 300 Industrial Park Rd, Starkville, Mississippi 39759, USA 

and must be 

accompanied by a letter describing the problem in detail along with a copy of your dated proof-of-
purchase and a telephone number. 

 

12.

  This warranty gives you specific rights, and you may also have other rights, which vary from 

state to state. 

 
 
 

Rev 04/08/2011 

Summary of Contents for MFJ-249C

















Reviews: