Meyer SXI 720 Owner/Operator’S Manual & Parts Book Download Page 40 | Manualshive

Page: 40 / 132

Meyer SXI 720 Owner/Operator’S Manual & Parts Book Download Page 40

Meyer Manufacturing Corporation

- 40 -

PB-SXIC

8.1.3 Monthly Lubrication (Every 260-300 Loads*)

Grease (2) jack assembly zerks located on the front

face of the jack and grease (2) hitch zerks.

Grease the (1) front drive bearing supporting the third

auger drive shaft with approximately 2 pumps of grease. The
zerk is accessible by the right front side grease bank of the
spreader. Be careful not to over grease.

Grease the (2) front drive bearings supporting the first

reduction drive shaft with approximately 2 pumps of grease.
The zerks are accessible by the right front side grease bank of
the spreader. Be careful not to over grease.

Grease the (2) front drive bearings supporting the second and third reduction jackshafts with approximately 3

pumps of grease. The zerks are accessible by the left and right front side grease banks of the spreader. Be careful not to
over grease.

Grease (1) nylon bushing supporting the rear shaft of the 3rd auger assembly. The zerk is grease line fitted to the

left rear corner of the tank below the light bracket. Over greasing is not possible.

Grease (6) bearings on the right hand side drive shaft with approximately 1 pump of grease. The second bearing

is grease line fitted to the right front side grease bank. The front bearing is accessible behind the front belt drive shield.
The remaining rear bearings are located along the right hand side of the spreader tank. The zerks are accessible through
the steel shielding.

Grease the hubs through the zerk in each hub. Be careful not to over grease and force the seal out of the back

side of the hub. (Not including 865 brake hubs.)

Grease (2) T-post hold down sleeve zerks located at the rear left side of the spreader.

Grease front belt tensioner pivot.

Grease the (1) front drive bearing supporting the second reduction jackshaft with approximately 2 pumps of

grease. The zerk is accessible by the right front side grease bank of the spreader. Be careful not to over grease.

Grease the (2) front drive bearings supporting the first reduction jackshaft with approximately 1 pump of grease.

The zerk is accessible by the left front side grease bank of the spreader. Be careful not to over grease.

L1

/

L15

L16

L17

L18

L19

L20

L21

L22

L23

L24

L25

«
...
38
39
40
41
42
...
»

Summary of Contents for SXI 720





































































































































Reviews:

No comments