background image

Meyer Products LLC warrants to Purchaser the following:
Meyer Products LLC, warrants to the original purchaser for a period of one year from the date of purchase of Meyer® brand 
spreader products that they will be free from defects in materials or workmanship, with the exceptions stated below. No 
person is authorized to change this warranty or to create any additional warranty on Meyer® products.

Meyer Products LLC will repair any product that proves to be defective in materials or workmanship. In the event repair is not 
possible or practical (as determined by Meyer Products LLC in its sole discretion), Meyer Products LLC will either replace the 
product with a new product of similar model and price, or refund the full purchase price, as determined by Meyer Products 
LLC. Customer must keep the complete spreader system serviced/maintained as recommended by Meyer Products LLC.

This warranty does not cover:
• Problems caused by failure to follow the product instructions, or failure to maintain the product as described in the Operator’s
Manual;
• Damage resulting from rust, corrosion
• Damage caused by usage that is not in accordance with product instructions (use of the spreader for any purpose other
than spreading approved material is considered misuse and abuse);
• Any spreader, or any part, component, or assembly thereof, which has been modified or altered;
• Problems caused by using accessories, parts, or components not supplied by Meyer Products LLC;
• Cost of tax, freight, transportation or storage charges, environmental charges, solvents, sealants, lubricants or any other
normal shop supplies.
• Problems caused by collision, fire, theft, vandalism, riot, explosion, lightning, earthquake, windstorm, hail, water, flood, or
any other Acts of God;
• Liability for damage to property, or injury to, or death of any person arising out of the operation, maintenance or use of the
covered product;
• Products with missing or altered serial numbers;

How To Get Service:
• It is the responsibility of the original purchaser to establish the warranty period by verifying the original delivery date. A bill
of sale, cancelled check or some other appropriate payment record may be kept for that purpose. It is recommended, but 
not required, that the consumer verify the original delivery date by immediately returning the attached Warranty Registration 
Card.
How State Law Applies:
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

WARRANTY

Meyer Products LLC

18513 Euclid Ave. • Cleveland, Ohio 44112-1084

Phone 486-1313 (Area Code 216)

www.meyerproducts.com• email info@

meyerproducts.

com

PRINTED IN U.S.A. 

FORM NO. 41933 (04/18/11)

Meyer Spreaders are protected by one or more of the following patents: 6698997, CA 2,415,540 C, 7588195, 8448882, 8505837, 8523086, 

8657208, 6186731, 6,793,154 B2, 6722590, 6715703, 6978952, 6932287, 8505838, 8827002, 5842649, CA 2,435,106 C, 6364598.

Summary of Contents for 31125













Reviews: