background image

 

14 

 

 
 

IMPORTANT 

 

The  operator  must  use  the  appropriate  PPE  (personal  protective  equipment).  For  example: 
use  cap  in  hair  preventing  it  from  locking  up  in  moving  parts  and  appropriate  gloves  to 
guarantee hygiene when handling food, also protects the operator during the process. 

 

IMPORTANT 

 

The  manufacturer  is  not  responsible  for  possible  direct  or  indirect  damages  caused  by  non-
compliance with rules and instructions in this manual. 

 
 
 

 5. Cleaning and Maintenance 

 

 
 
5.1 Procedures for Cleaning and Products to be used

 

 
 

Your  device  was  built  with first  class  materials, so  use  it  correctly  and  get great  satisfaction. 

Keep it always clean and well maintained, by doing this, your device will have longer life cycle. 

 
You must do daily cleaning on the device for a good operation and durability. 
 

 

                   

         WARNING! 

 

Before performing maintenance or cleaning, ensure that the On/Off Switch is in position "0" 

(off) and that the plug is disconnected from the mains.

 

 

 

              
                   WARNING! 

 

Do not use water jet to clean the device. 

 

 

IMPORTANT 

 

This device is not intended to be fully immersed in water for cleaning.  
Follow  the instructions  below to  learn which parts  can  be  immersed  and which  one  needs 
special care. 

 
 
Demountable  parts  (Disc,  Tray  and  Nozzle)  should  be  removed  from  the  device  (as 

instructions  on  item  4.3)  and  washed  with  warm  water  and  mild  detergent.  Thoroughly  clean  the 
corners, eliminating waste from the food.  

 

Summary of Contents for BIMG RDA Series





















Reviews: