METRON daeg SPO2 User Manual Download Page 9

 

 

 

www.metron-biomed.com

 

daeg Quick Start 

 
 

daeg  Startup 

 

1. Connect daeg’s Finger Probe to the main daeg unit, 

and switch the daeg unit 

on

.  

 
The daeg must be powered by the 9VDC 400mA 
power supply or by 4 AA alkaline batteries loaded 
into the unit’s battery compartment.   
 

2. The version number of the firmware will be briefly 

displayed, followed by the first display screen 
(below). The unit is immediately outputting the 
simulation as displayed. 

 
3. Apply the oximeter’s sensor to the daeg finger 

probe. The sensor’s transmitter must be on the 
bottom (unlabeled) side of the daeg finger.

  

 
 
 
 
 
 
 
 
 
 

1. To adjust the simulation settings, use the 

F2

 

function key to select the “active” parameter. The 
active parameter is marked with an asterisk (*).  

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Note:

  Menu items at the bottom of the display are 

activated/accessed using the F1, F2, and F3 function 
keys. 

 
2. Adjust the active parameter using the yellow Up 

and Down arrow keys on the keypad, then press 

enter

 to confirm the change.    

                                                       

 

 
3. To change the simulation setting for oximeter 

model (Make), Ambient Light, Pigmentation, or to 
select an automated simulation sequence, select the 

F3

 function key to go to the second display screen. 

 
4. To access additional test and auxiliary functions, 

press the 

F1

 function key while in the first or 

second screen display.

 

 

 

Additional / Auxiliary functions include:  

  Alarm Tests, Print functions, Remote Control Operation, 

Probe Tests, and Simulation Setup.

 

                                        
 
 
 
 
 
                                   
 
   
   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Release 

------------------

STATUS --------

--------Preset  : 

Manual 

SpO2  :    96  % 
Rate  :    60  BPM 
P.ampl 

:  100  % 

 
FUNC. 

           

 

       

displ-1

 

F1 

F2 

F3 

----------------- 

STATUS ----------------

Preset 

Manual 

SpO2 

:    96 

Rate 

:    60 

BPM 

P.ampl 

:  100 

%

 

 

FUNC.

 

    

 

        

displ-1

 

METR  N 

SpO2 Analyzer 

LED-test 
      Red 
      IR 

F1 

F2 

F3 

daeg 

no 

clear

 

yes 

enter

 

 

1

   

ABC

 

 .  ,  #  $ 

7    

STU 

 

template 

esc 

 

2

    

DEF

 

3    

GHI

 

4    

JKL

 

9    

YZ?

 

8   

VWX

 

0     

_- 

/

 

6   

PQR

 

5   

MNO

 

 

on 

off 

Battery Compartment 

daeg finger probe 

Label side to bottom.  

SpO2 sensor  

Red, IR light source 
introduced on unlabeled 
side of daeg finger.  

Daeg Operation / Simulation 

Summary of Contents for daeg SPO2





















Reviews: