background image

CAUTION! 

 All accessories, switches, climate 

controls panels, and especially air bag indicator 

lights must be connected before cycling the 

ignition. Also, do not remove the factory radio 

with the key in the on position, or while the 

vehicle is running. 

Metra. The World’s Best Kits.

®

 

MetraOnline.com 

© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION 

REV. 3/16/18 INST95-6523

I N S TA L L AT I O N I N S T R U C T I O N S

95-6523

KIT FEATURES

•  ISO DDIN radio provision
•  Custom texture

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Radio mounting brackets • D) (4) White plastic panel clips • E) (8) 5mm x 12mm Phillips Screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver  
• 86-5618 radio removal tool 
• 86-3528 radio removal tool 

TABLE OF CONTENTS

Dash Disassembly ..................................................2
Kit Assembly ..........................................................3

WIRING & ANTENNA CONNECTIONS

 (sold separately)

Wiring Harness: 70-1784 or XSVI-6523-NAV
Antenna Adapter: 40-VW10 or 40-EU10

A

B

C

D

E

Ram 

Promaster

 

2014-up*

*Visit 

MetraOnline.com

 for up-to-date vehicle specific applications.

Summary of Contents for 95-6523









Reviews: