Metabo HC 260 C, Original Instructions Manual

Page: 21 / 192

21
ENGLISH en
5.6 Fhuce profile installation
1. Remove fhuce carrier support
bracket (60) from fhuce carrier (57) .
Take care not to loose the two guide
pins (61) in the fhuce carrier support
bracket.
2. Fasthu fhuce carrier support bracket
(60) with two hexagon head screws
(59) to infeed table.
3. Attach fhuce carrier to fhuce carrier
support bracket again.
4. Slide two carriage bolts (62) into the
fhuce extrusion (63) and attach to
fhuce carrier with two self-locking
hexagon nuts (58) .
5. Fit extrusion hud caps (64) to both
huds of the fhuce extrusion.
6. Screw the cover plates (55) together
and fasthu to fhuce carrier using two
crosshead screws (56) .
7. Adjust the two set screws so that the
positive stops of the jointer fhuce are
set exactly to 45° and 90° (use try
and mitre squares).
5.7 Power-supply connec-
tion
B
Danger!
High voltage
Operate in dry huvironmhut only.
Operate machine only on a power
source matching the following
requiremhuts (see also "Technical
Specications"):
 fuse protection by a residual cur-
rhut operated device (RCD) of
30 mA shusitivity;
 outlets properly installed,
earthed or grounded, and tested;

5-wire three-phase outlets with
neutral lead.
 Whhu a dust collector is used it
must also be properly earthed.
Position power supply cable so it
does not interfere with the work and
is not damaged.
Protect power supply cable from
heat, aggressive liquids and sharp
edges.
Use only exthusion cables with a suf-
ficihut lead cross section.
Do not pull on power supply cable to
unplug.
B
Check direction of rotation!
(machines with 3-phase motor only):
Dephuding onthe phase sequhuce
the cutterblock may turn in the wrong
direction. This can cause damage to
the machine and work piece. It is
therefore necessary to check the
direction of rotation after initial com-
missioning and every time the
machine is connected to a differhut
outlet.
If the direction of rotation is incorrect
the phases must be changed on the
supply line or mains connection by
an electrician.
The planer/thicknesser HC 260 can
either be operated as surface planer or
thickness planer:
6.1 Surface planer mode
3
Note:
Surface planing is used to level an
unevhu surface (= jointing), for exam-
ple the edges of a plank.

The work piece rests on top of the
infeed table.

The work piece is cut on the under-
side.

The feed direction for the work piece
is exactly opposite than that for
thickness planing.
Work piece dimhusions
Preparation
A
Danger!
Always unplug before servicing!
1. Turn setting screw (65) clockwise to
the hud position.
2. Swing chip chute down.
3. Turn both left and right lock lever
outwards.
4. Place outfeed table (66) on machine
– both pins on the machine housing
must hugage in the lower slots of the
outfeed table guide.
3
Note:
The pins must trigger the hud switch.
Only thhu the machine can be
switched on.
5. Secure outfeed table (66) with both
lock levers (67) .
6. Set the infeed table to 2.0 to 2.5 mm
by turning the height adjustmhut.
7. Crank thicknesser bed up to 120 mm
height.
8. Place dust collector connector (this
is not the chip chute mhutioned in
step 1!) below the infeed table into
the machine. Observe correct posi-
tion of the dust collector connector:

suction port points outwards;
55
56
57
58
59
60
61
64
63
62
6. Operation
lhugth width height
use push block
(feeding aid) if less
than 250 mm
max.
260 mm
5 mm
min.
use extra work piece
supports or helper if
over 1500 mm
65
66
67