5
English
(4) Disconnect the Nailer from the air source before
making any adjustments, changing accessories,
or storing the Nailer.
Such preventive safety
measures reduce the risk of starting the Nailer
unintentionally.
(5) Store the Nailer when it is idle out of reach of
children and other untrained persons.
A Nailer is
dangerous in the hands of untrained users.
(6) Maintain the Nailer with care.
Keep the
Nailer Clean and lubricated for better and safer
performance.
(7) Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that may a
ff
ect the Nailer's operation.
If damaged, have the Nailer serviced before using.
Because of high air pressure in the Nailer, cracks in
the surface are dangerous. To avoid this, do not drop
the Nailer or strike the Nailer against hard surfaces;
and do not scratch or engrave signs on the Nailer.
Many accidents are caused by poorly maintained
Nailers. There is a risk of bursting if the Nailer is
damaged.
(8) Do not use the Nailer that is not in proper
working order. Tags and physical segregation
shall be used for control.
(9) Use only accessories that are identi
fi
ed by
metabo HPT for the speci
fi
c Nailer.
Use of an
accessory not intended for use with the speci
fi
c
Nailer , increases the risk of injury to persons.
(10)
Use only those fasteners listed in the
Accessories section of this manual.
Fasteners not
identi
fi
ed for use with this Nailer by metabo HPT are
able to result in a risk of injury to persons or Nailer
damage when used in this Nailer.
4. Service
(1) Tool service must be performed only by quali
fi
ed
repair personnel.
(2) When servicing a Nailer, use only identical
replacement parts. Use only authorized parts.
(3) Use only the lubricants supplied with the Nailer
or speci
fi
ed by metabo HPT.
5. Air source
(1) Never connect to an air source that is capable
of exceeding 200 psi (13.7 bar 14 kgf/cm
2
) if a
regulator fails.
Over pressurizing the Nailer is able to result in
bursting, abnormal operation, breakage of the Nailer
or serious injury to persons.
DO NOT EXCEED 120 psi (8.3 bar 8.5 kgf/cm
2
).
Use only clean, dry, regulated compressed air at the
rated pressure or within the rated pressure range as
marked on the Nailer.
Always verify prior to using the Nailer that the air
source has been adjusted to the rated air pressure or
within the rated air-pressure range.
(2) Never use reactive gases such as oxygen,
carbon dioxide, combustible gases or any
bottled gas as an air source for the Nailer.
Such
gases are capable of explosion and serious injury to
persons.
6. Others
(1) Before starting work, check the nailing operation
switching device.
This metabo HPT nailer includes a nailing operation
switching device.
Before starting work, check the setting of the
operation switching device.
If the switching device is not set properly, the Nailer
will not operate correctly.
(2) Always select the switching device that is
appropriate to the application and the training of
the operator.
(3) When switching between SINGLE SEQUENTIAL
and CONTACT, disconnect the air hose and
remove all nails.
(4) When the hook is attached, operate only with
SINGLE SEQUENTIAL ACTUATION MECHANISM
and not with CONTACT ACTUATION MECHANISM.
(5) Be careful of double
fi
re and being hit by the
Nailer due to spring back (“recoil”).
After driving
a nail, the Nailer may recoil causing it to move away
from the work surface.
To reduce risk of injury always manage recoil by:
1) always maintaining control of the Nailer.
2) allowing recoil to move the Nailer away from work
surface.
SAFETY
— Continued
WARNING
000Book̲NV83A5̲US̲metabo.indb 5
000Book̲NV83A5̲US̲metabo.indb 5
2022/05/19 11:02:35
2022/05/19 11:02:35