Dismantling / Assembly ( see fig. 2 - 6
)
1. Follow the safety measures.
Disconnect the pump!
2. Press together the filter cover (1) laterally and take it out of the
pump (8).
3. Pull the filter sponge (2) out of the filter cover (1).
4. Turn the inlet lid (3) counterclockwise and take it out of the pump (8).
5. The front bearing support (4.4) and an axial bearing washer (4.3)
are situated in the inlet lid (3) or on the axle (4.2) respectively.
6. Pull the rotor (4) out of the pump (8). Attention: The rotor (4) has a
very strong magnetic field!
7. Thoroughly pull the axle (4.2) out of the pump (8).
8. Laterally push on the rear filter cover (6) and pull it off the pump (8).
9. Push the rear bearing support (4.5) including the axial bearing
washer (4.3) out of the pump; you may find a pen to be helpful to
accomplish this.
10. Insert this pen in the small bore at the pump’s rear side (8) and
use it in order to push the rear bearing support (4.5) including
the axial bearing washer (4.3) out of the pump.
11. Clean all components - please use clear water only - so that they
allow to be easily moved. Do not use sharp-edged objects.
12. Proceed as follows in order to reassemble the pump:
12.1. Put the rear bearing support (4.5) including the axial bearing
washer (4.3) onto the axle (4.2) and insert it in the pump (8).
12.2. Put the rotor (4) onto the axle (4.2). Caution: The rotor (4) has a
very strong magnetic field, which will pull the rotor into the
pump (8)!
12.3. Put the front bearing support (4.4) including the axial bearing
washer (4.3) onto the axle (4.2).
12.4. Insert the inlet lid (3) in the pump (8), holding it in the same
position as when you took it out of it, then turn it clockwise until
it stops.
12.5. Insert the filter sponge (2) in the filter cover (1).
12.6. Insert the front (1) and rear (6) filter covers in the pump (8).
To ensure proper functioning, repeat the above procedure frequently,
depending on clogging and working time.
Maintenance
In order to prolong the service life of your pump and to keep it in good
operating condition, it is recommended to carry out maintenance and
cleanup regularly.
This can be done by everyone, quickly and easily.
See
"Dismantling/Assembly"
.
Servicing intervals
- In the beginning check performance of your pump every day.
If necessary, clean the filters.
- Since servicing intervals (complete cleanup) will vary depending
on pond pollution, repeat the periodic service to your pump in
accordance with the requirements given.
Should you determine that there are damaged or worn parts, do replace
them. See "Spare parts".
Winter / Pump care
Protect your pump from freezing-in!
Take the pump out of your pond in autumn.
Clean the pump completely following the outlined instructions.
During the winter months store the pump in a frost-resistant room.
Spare parts
For ordering spare parts, please indicate the pump type, the de
signation and the Art.-No. as per table below (see also fig.
5 - 6
).
Item Designation
Pump
Type
Art-No.
1
Filter cover front
M 2600, M 3500, M 4500
168/009109
2
Filter sponge
M 2600, M 3500, M 4500
168/009079
3
Lid incl. sealing ring
M 2600, M 3500, M 4500
168/009110
4
Rotor complete
M 2600
168/009111
M 3500
168/009112
M 4500
168/009113
6
Filter cover back
M 2600, M 3500, M 4500
168/009081
7
Handle/Stand
M 2600, M 3500, M 4500
168/009088
GUARANTEE CONDITIONS
This pump comes with a
36-month
guarantee that is effective from the
date of delivery. The invoice will be the proof of the date. In case of
damages due to defects in material or manufacturing, we shall either do a
free repair during the guarantee period or replace the damaged part, the
choice being ours’.
Damages that occur due to installation and operating errors, lime
deposits, insufficient care, frost action, normal wear and tear or improper
repair attempts will not come under this guarantee. The guarantee will not
be valid in case of modifications to the pump, e.g. cutting off the line
connection or the line cord. We will not accept responsibility for
consequential damages resulting from breakdown of the pump or
improper operation.
When making use of the guarantee, please send us the pump, along with
the corresponding invoice, free of charge via the specialist dealer who
sold you the pump.
Waste disposal
waste disposal of electronic devices by the user in private households
of the EU
It is not allowed to dispose the product along with the regular waste disposal,
instead it has to be collected separately. It is your responsibility to dispose
and recycle the device in a proper place and protect the environment through
this. More information, where to dispose your devices can be obtained at the
local departments.
8
9
130-003064_01/07_M 2600 / M 3500 / M 4500_BA 06.02.2007 13:15 Uhr Seite 11