background image

ELECTRICAL SYSTEM 

11-3 

ELECTRICAL CONNECTOR WIRING 
DIAGRAM (STANDARD 7RV BLADE) 

 
 
 
 
 
 
 
 
 
 

 

GD = GROUND WHITE 
TL = TAIL, BROWN WIRE 
LT = LEFT TURN YELLOW 
RT = RIGHT TURN GREEN 
AX = BATTERY BLACK 
EB = ELECTRIC BRAKES BLUE 

 

ELECTRICAL CONNECTOR WIRING 
DIAGRAM (STANDARD 6-WAY) 

 
 
 
 
 
 
 

S* = BRAKES   BLUE 
GD = GROUND WHITE 
TM = TAIL/MARKER LIGHTS BROWN 
RT = RIGHT TURN GREEN 
LT = LEFT TURN YELLOW 
A* = CLEARANCE LIGHTS BLACK 

 

12 Volt Sealed Lead-Acid Battery 

(Breakaway Battery) 

To maximize the life of the battery the 
following conditions should be met: 

1.

 

Avoid over or undercharge. This is the 

single worst enemy of lead-acid batteries. 

2.

 

Batteries should not be stored in a 

discharged state or at elevated ambient 
temperatures. 

3.

 

Avoid exposing batteries to heat! 

Service life is shortened considerably at 
ambient above 30 deg C (86 deg F) 

4.

 

Due to the characteristics of this 

battery, after six to nine months of 
storage, the battery should be recharged. 

5.

 

Charge battery at the proper rate. 

Current should be limited to 1.2 amps or 
less 

6.

 

Provide adequate air circulation when 

charging battery. Do not charge battery 
in any other containers beside supplied 
battery box. 

7.

 

Do not place batteries in close 

proximity to objects which can 
produce sparks or flames. 

8.

 

Do not expose battery case to organic 

solvents or adhesives. 

9.

 

Do not attempt to disassemble 

batteries. Contact with sulfuric acid 
may cause harm. 

10.

 

Fasten batteries tightly and make 

provisions for shock absorption if 
exposure to shock or vibration is likely. 

11.

 

Do not throw batteries into fire: 

batteries so disposed may rupture or 
explode. 

 

 

Summary of Contents for GOOSENECK LIVESTOCK TRAILER






































Reviews: