manualshive.com logo in svg

MERRICK MC3 90.10.EX, Operation And Maintanance Manual

Share
Download
MERRICK MC3 90.10.EX Operation And Maintanance Manual Download Page 33

 

MC³ 90.10.EX O&M Manual  

 

- 26 -  

Date/Time 

For setting the date and time parameters, follow the direction given the  Entering New Values 
section found on page 21. 

Analog Input 

 

The analog inputs can  be mapped to Analog Setpoint or Panel Meter functions.  Two analog 
inputs are available when there are two PCIO boards installed into the controller.  Once the inputs 
are mapped, you should adjust the high, low and scaling values.  The  Analog I/O Diagnostics 
(page  34) displays the active counts for the analog inputs and can be used to determine the high 
and low values. 

Analog Setpoint 

When you intend to use an analog signal for the setpoint, an Analog Input Source must be set for 
this input.  The analog input selected is used for the setpoint when the Setpoint method is 
Remote Analog Input.   

Panel Meter 

This selection is used to display a value of an analog input to be used for display purposes only.  
The value is scaled to a user-defined value.  The value can be set in the numeric parameter 
selection (see below).    

Analog Input Source Settings 

 The source used is analog input number 1 on PCIO board number 1. 

 The source used is analog input number 2,  which is located on the PCIO board 

number 2. 

 The value that is used for the function selected is always 0. 

 The value used is controlled through a register using the serial port. 

Analog Input Numeric 

Low Values 

This value is the counts representing the zero level of the incoming signal.  When the input signal 
is set to 4-20mA (2-10V) input then this value should be 200,000 counts.  If the input is set to 0-
20mA (0-10V) then the zero level should be close to 0 counts.  Limits are minimum of 0 and a 
maximum of 1,040,000. 

High Values 

This value is the representation of the 100% value of the incoming signal.  Normally this value will 
be 1,000,000 counts representing 100% (20mA or 10V) of the incoming signal.  Limits are 
minimum of 1 and a maximum of 1,040,000. 

Maximum Scale Values 

This is the value representing the full-scale value used for scaling the input.  This value should be 
associated with the analog input counts it is to represent 

Summary of Contents for MC3 90.10.EX




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands