background image

2

CONTENTS

PAGE

SAFETY INSTRUCTIONS . . . . .2

CARTON INVENTORY . . . . . . .3

ACCESSORIES . . . . . . . . . . . 3

SPECIFICATION . . . . . . . . . . .4

TOOLS REQUIRED . . . . . . . . .4

PREPARE & TEST THE DOOR . .4

DOOR REQUIREMENTS . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . .6

INSTALLATION . . . . . . . . .7-10

CONNECT ELECTRIC POWER .10

INSTALL MULTI-FUNCTION DOOR

CONTROL . . . . . . . . . . . . . .10

INSTALL THE PROTECTOR

SYSTEM . . . . . . . . . . . . . . .11

AUTO CLOSE . . . . . . . . . . . .13

ADJUSTMENT . . . . . . . . .14-17

WIRELESS PROGRAMMING 18-19

REPAIR PARTS . . . . . . . . . . .20

DIAGNOSTIC CHART . . . . . . .21

TROUBLESHOOTING . . . . . . .22

CARE OF YOUR OPENER . . . . 23

OPERATION OF YOUR OPENER23

WARRANTY . . . . . . . . . . . . .24

WARNING

• Failure to comply with the following instructions may result in serious personal injury or property damage.

• Read and follow all instructions carefully.

• The garage door opener is designed and tested to offer safe service provided it is installed and

operated in strict accordance with the instructions in this manual.

These safety alert symbols mean

WARNING

: A possible risk to personal safety or

property damage exists.

NOTE: If your garage has no service entrance door, a CM1702 outside quick release must be installed.

This accessory allows manual operation of the garage door from outside in case of power failure.

START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS

The Protector System

TM

must be used for all installations

where the closing force as measured on the bottom of the

door is over 400 N (40 kgf).

Excessive force will interfere with

the proper operation of the Safety Reverse System or damage

the garage door.

S

PECIAL NOTE: Merlin strongly recommends that The

Protector System

TM

be installed on all garage door openers.

After installation, ensure that the parts of the door do not

extend over public footpaths or roads.

Install the wireless wall control (or any additional wall control)

in

a location where the garage door is visible, at a height of at

least 1.5 m and out of the reach of children. Do not allow

children to operate push button(s) or transmitter(s).

Serious

personal injury from a closing garage door may result from

misuse of the opener.

Permanently fasten the Warning Labels in Prominent Places,

adjacent to Wall Controls and on manual release mechanism as

a reminder of safe operating procedures.

Activate opener only when the door is in full view, free of

obstructions and the opener is properly adjusted. No one

should enter or leave the garage while the door is in motion.
Automatic Door-

The door may operate unexpectedly, therefore

do not allow anything to stay in the path of the door.

Do not allow children to play near the door, or with door

controls. Keep remotes away from children.
Disconnect electric power to the garage door opener before

making repairs or removing covers.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid hazard.

This opener should not be installed in a damp or wet space

exposed to weather.

To avoid damage to very light doors (such as fibreglass,

aluminium or steel doors), an appropriate reinforcement should

be added. To do so, contact the door manufacturer.

SAVE THESE INSTRUCTIONS

Keep garage door balanced

.

Do not let the garage door

opener compensate for a binding or sticking garage door.

Sticking, binding or unbalanced doors must be repaired

before installing this opener.

Do not wear rings, watches or loose clothing

while

installing or servicing a garage door opener. Wear gloves,

safety goggles and suitable protective clothing where

appropriate.

Frequently examine the door installation,

in particular

cable, springs and mountings for signs of wear, damage or

imbalance. Do not use if repair or adjustment is needed

since springs and hardware are under extreme tension

and a fault can cause serious personal injury.
To avoid serious personal injury from entanglement,

remove all ropes, chains and locks connected to the

garage door

before installing the door opener.

Installation and wiring

must be in compliance with your

local building and electrical codes.

The safety reverse system test is very important.

Your

garage door

MUST

reverse on contact with a 40 mm

obstacle placed on the floor. Failure to properly adjust the

opener may result in serious personal injury from a closing

garage door.

Repeat the test once a month and make

any necessary adjustments.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

Use the

Manual Release

only for the seperation of the

carriage from the drive and - if possible - ONLY with the

door closed. Do not use the red handle to push the door

up or pull it down. Operation of the emergency release can

lead to uncontrolled movements of the door, if springs are

weak or broken or if the door is unbalanced. Mount the

release handle of the emergency release at a height less

than 1.8 m from the floor.

Summary of Contents for MJ3800

























Reviews: