Meridian SEED EXPRESS 240 RT Operator'S Manual Download Page 38

Page: 38 / 96

9. Open the slide gate from the seed tender

control panel or use the wireless remote

controltothedesiredseedflow.

IMPORTANT

Close the slide gate and stop the conveyor prior

to the planter’s seed box being completely full. If

the seed box requires additional seed, start the

conveyor without opening the slide gate; this will

use the seed that is already on the conveyor. This

methodwillalsohelppreventoverfillingofthe

seed box or the seed tender’s pan.

10.

Whentheplanterisfilled,closetheslidegate

and then stop the conveyor belt.

11.

Whenfinishedloadingtheplanter,returnthe

conveyor to the transport position and install

the lock pin and retaining clip.

Note:

If the seed tender is being moved within

afieldlocation,itisnotnecessarytoinstallthe

damper mechanism to the conveyor.

Summary of Contents for SEED EXPRESS 240 RT

































































































Search results

Summary of Contents for SEED EXPRESS 240 RT

Reviews:

Related manuals for SEED EXPRESS 240 RT

Brands by name

Popular brands

Meridian SEED EXPRESS 240 RT, Operator'S Manual

Search results

Summary of Contents for SEED EXPRESS 240 RT

Reviews:

Related manuals for SEED EXPRESS 240 RT

Brands by name

Popular brands