Meridian SEED EXPRESS 240 RT Operator'S Manual Download Page 32

Page: 32 / 96

6.2 PRE-OPERATION CHECKLIST

EfficientandsafeoperationoftheMeridianBulk

Seed Tender system requires that each operator

reads and follows the operating procedures and all

related safety precautions outlined in this section.

A pre-operational checklist is provided for the

operator. It is important for both personal safety

andmaintainingtheefficientoperationofthe

delivery system that this checklist be followed.

Before operating the delivery system and each

time thereafter, the following areas should be

checked:

1. Lubricate the machine, as outlined and shown

in the Grease/Lubrication Location Diagram

in the Maintenance section of this manual.

Follow the prescribed schedule.

Checktheenginefluidlevels,fuel,and

crankcase oil. Add, as required.

IMPORTANT

The engine warranty is void if the engine is run

without oil.

3. Check hardware and fasteners; seed tender

frame to trailer tie-downs, hitch bolts, trailer

hitch to trailer bolts, and all other fasteners.

Tightentotheirspecifiedtorque.

4. Make sure the wheel bolt lug nuts are tight.

5. Check the tires and ensure that they are

inflatedtotheirspecifiedpressure.

6. Remove all entangled material.

7. Visually inspect the conveyor and frame for

damage.

8. Test the Break-Away brake unit and the trailer

brakes.

a. Make sure the trailer brakes are operating

properly.

b. Make sure the trip wire to the break-away

switch is connected to the tow vehicle.

c. Make sure the pin is correctly installed in

the break-away switch.

d. Press the Test button. The indicator

should illuminate green. If the red light

illuminates, the battery charge is low.

Refer to the Break-Away System in the

Maintenance section for instructions on

charging the battery.

Checkthefluidlevelinthehydraulictank.Add

fluid,asneeded.

10.

Starttheengineandcheckthefilterstatus

indicator.Replacethefilterifindicated.

11. Check the tension of the delivery belt. Follow

the instructions in the manual to correct the

tension and/or alignment.

12. When the machine is operating, check the

alignment of the delivery belt. Follow the

instructions in the manual to correct the

tension and/or alignment.

Summary of Contents for SEED EXPRESS 240 RT

































































































Search results

Summary of Contents for SEED EXPRESS 240 RT

Reviews:

Related manuals for SEED EXPRESS 240 RT

Brands by name

Popular brands

Meridian SEED EXPRESS 240 RT, Operator'S Manual

Search results

Summary of Contents for SEED EXPRESS 240 RT

Reviews:

Related manuals for SEED EXPRESS 240 RT

Brands by name

Popular brands