Meridian SEED EXPRESS 240 RT Operator'S Manual Download Page 37

Page: 37 / 96

2. Remove the lock pin from the damper

mechanism. The conveyor may need to be

lowered slightly to remove the tension from the

lock pin. Store the pin in a safe location.

3. Turn the key switch to the ON position.

4. Move the fuel valve lever to the ON position

(towardthefrontofthemachine).

5. To start a cold engine, move the choke lever to

theCLOSEDposition(towardthebackofthe

machine).Also,movethethrottlelever1/3the

distance of the full open position.

6. Start the engine and move the throttle lever to

run the engine at full speed.

7. Rotate the conveyor to the desired location.

8. Start the conveyor from the seed tender

control panel or use the wireless remote

control.

Summary of Contents for SEED EXPRESS 240 RT

































































































Search results

Summary of Contents for SEED EXPRESS 240 RT

Reviews:

Related manuals for SEED EXPRESS 240 RT

Brands by name

Popular brands

Meridian SEED EXPRESS 240 RT, Operator'S Manual

Search results

Summary of Contents for SEED EXPRESS 240 RT

Reviews:

Related manuals for SEED EXPRESS 240 RT

Brands by name

Popular brands