background image

GENERAL INFORMATION

15

IMPORTANT: Indicates information or instructions that are

necessary for proper operation and/or maintenance.
Read this manual carefully. Learn the difference in handling

characteristics between a Mercury Jet Drive boat and a propeller

driven boat including:

Steering at low power/throttle ‑

 unlike propeller driven boats,

the Mercury Jet Drive boat tends to lose steering control as

less water is drawn in and expelled. Increase power/throttle

slightly to regain steering.

Maneuverability ‑

 the Mercury Jet Drive is highly

maneuverable at higher speeds; more so, than propeller

driven boats. Use caution when turning to prevent spinouts.

Steering in reverse ‑ 

unlike propeller driven boats, turning the

steering wheel turns the bow of the boat in the 

same direction.

If you have any questions, contact your dealer.
Safety and operating information that is practiced along with using

good common sense can help prevent personal injury and product

damage.

Boat Horsepower Capacity

!

 WARNING

Exceeding  the  boat's  maximum  horsepower  rating  can  cause

serious injury or death. Overpowering the boat can affect boat

control and flotation characteristics or break the transom. Do not

install an engine that exceeds the boat's maximum power rating.

Summary of Contents for 200 Sport-Jet





















































































Reviews: