Mercury 135 Verado FourStroke Operation And Maintenance Manual Download Page 95

Page: 95 / 123

• Tilt Support Lever ‑ Lubricate through fitting.

a -

Swivel bracket

b -

Tilt support lever

• Tilt Tube ‑ Lubricate through fitting.

a -

Tilt tube fitting

4. Lubricate the following with Quicksilver or Mercury Precision Lubricants

2‑4‑C with PTFE or Extreme Grease.

WARNING

Incorrect cable lubrication can cause hydraulic lock, leading to serious

injury or death from loss of boat control. Completely retract the end of the

steering cable before applying lubricant.

Tube Ref

No.

Description

Where Used

Part No.

Extreme Grease

Steering cable

8M0071842

2-4-C with PTFE

Steering cable

92-802859A 1

29759

29757

MAINTENANCE

eng

Summary of Contents for 135 Verado FourStroke




























































































































Search results

Summary of Contents for 135 Verado FourStroke

Reviews:

Related manuals for 135 Verado FourStroke

Brands by name

Popular brands

Mercury 135 Verado FourStroke, Operation And Maintenance Manual

Search results

Summary of Contents for 135 Verado FourStroke

Reviews:

Related manuals for 135 Verado FourStroke

Brands by name

Popular brands