Mercury 135 Verado FourStroke Operation And Maintenance Manual Download Page 102

Page: 102 / 123

4. Remove the vent plug and fill/drain plug and drain lubricant.

a -

Vent plug

b -

Fill/drain plug

GEARCASE LUBRICANT CAPACITY

Gearcase lubricant capacity is approximately 970 ml (32.8 fl oz) for right hand

rotation gearcases and 900 ml (30.4 fl oz) for left hand rotation gearcases.

GEARCASE LUBRICANT RECOMMENDATION

Mercury or Quicksilver High Performance Gear Lubricant.

CHECKING LUBRICANT LEVEL AND REFILLING GEARCASE

1. Place the outboard in a vertical operating position.
2. Remove the vent plug/sealing washer.
3. Remove the fill/drain plug. Place the lubricant tube into the fill hole and

add the lubricant until it appears at the vent hole.

a -

Vent hole

b -

Fill hole

IMPORTANT: Replace the sealing washers if damaged.

22692

22693

MAINTENANCE

eng

Summary of Contents for 135 Verado FourStroke




























































































































Search results

Summary of Contents for 135 Verado FourStroke

Reviews:

Related manuals for 135 Verado FourStroke

Brands by name

Popular brands

Mercury 135 Verado FourStroke, Operation And Maintenance Manual

Search results

Summary of Contents for 135 Verado FourStroke

Reviews:

Related manuals for 135 Verado FourStroke

Brands by name

Popular brands