Mercury 135 Verado FourStroke Operation And Maintenance Manual Download Page 76

Page: 76 / 123

4. Ensure the battery is equipped with a nonconductive shield to prevent

accidental shorting of battery terminals.

Verado Engine Battery Specifications

IMPORTANT: Verado engines require a 12‑volt absorbed glass mat (AGM)

marine starting battery that meets the minimum ratings.
For best performance, Mercury Marine does not recommend using the more

common flooded (wet cell) or gel cell type lead acid batteries for starting

Verado engines.
Each Verado engine must be equipped with its own starting battery.
If the boat application requires additional battery loads for boat accessories or

marine electronics, install an auxiliary battery, or batteries.
Choose a 12‑volt absorbed glass mat (AGM) battery that meets the following

ratings.

USA (SAE) Verado Starting Battery Rating

Required Verado starting

battery

12‑volt absorbed glass mat (AGM) battery

Required marine cranking amps

(MCA) and reserve capacity

800 minimum marine cranking amps with a

minimum reserve capacity of 135 minutes

RC25 rating

International (EN) Verado Starting Battery Rating

Required Verado starting battery

12‑volt absorbed glass mat (AGM)

battery

Required cold cranking amps

(CCA) and amp hours (Ah)

975 minimum cold cranking amps with a

minimum of 65 amp hours

NOTE: Do not use an engine starting battery that does not meet the specified

ratings. If a battery that does not meet the ratings is used, the electrical system

may perform poorly.

IMPORTANT: Boating industry standards (BIA, ABYC, etc.), federal standards,

and Coast Guard regulations must be adhered to when installing the battery.

Ensure that the battery cable installation meets the pull test requirements and

that the positive battery terminal is properly insulated in accordance with

regulations.

It is recommended (required in some states) that the battery be installed in an

enclosed case. Refer to regulations for your area.
When connecting the engine battery, hex nuts must be used to secure the

battery leads to the battery posts. Tighten the hex nuts to the specified torque.

MAINTENANCE

eng

Summary of Contents for 135 Verado FourStroke




























































































































Search results

Summary of Contents for 135 Verado FourStroke

Reviews:

Related manuals for 135 Verado FourStroke

Brands by name

Popular brands

Mercury 135 Verado FourStroke, Operation And Maintenance Manual

Search results

Summary of Contents for 135 Verado FourStroke

Reviews:

Related manuals for 135 Verado FourStroke

Brands by name

Popular brands