Mercury Security LP1501 Installations And Specifications Download Page 9

Page: 9 / 10

LP1501

DOC 10107-0064

REV 1.01

Page 9

Humidity:

5 to 95 % RHNC

Mechanical:

Dimension:

5.5 in. (140 mm) W x 2.75 in. (70 mm) L x 0.96 in. (24 mm) H without bracket
5.5 in. (140 mm) W x 3.63 in. (92 mm) L x 1.33 in. (34 mm) H with bracket

Weight:

3.6 oz. (103 g) without bracket
4.43 oz. (125.5 g) with bracket

UL294, 6

edition Performance Levels:

Feature

Level

Standby Power

Endurance

Line Security

Destructive Attack

These specifications are subject to change without notice

14. Additional Mounting Information:

Sources for the optional items shown below:



3-gang stainless steel blank cover. Available from:

Leviton: part number 84033-40
Graybar: part number 88158404



Magnetic switch set: G.R.I. part number: 505

FIELD WIRING

LP1501 WITH INCLUDED
MOUNTING PLATE

TO ETHERNET

NETWORK

OPTIONAL 3-GANG

JUNCTION BOX

OPTIONAL BLANK

COVER W/SCREWS

OPTIONAL MAGNETIC

TAMPER SWITCH

Summary of Contents for LP1501











Search results

Summary of Contents for LP1501

Reviews:

Related manuals for LP1501

Brands by name

Popular brands

Mercury Security LP1501, Installations And Specifications

Search results

Summary of Contents for LP1501

Reviews:

Related manuals for LP1501

Brands by name

Popular brands