manualshive.com logo in svg

Mercedes-Benz 171.456 2005, Installation Instructions Manual

Share
Download
Mercedes-Benz 171.456 2005 Installation Instructions Manual Download Page 11

 

5.  Find the kit-included contact plate (A, Figure 

24) and identify the FAKRA antenna male 
connector (B, Figure 24) and the power 
supply male connector (C, Figure 24). 
 

 

Figure 24                                                    

P82.70-5426-71

 

6.  Feed the power supply cable and FAKRA 

cable of the contact plate through the 
knockout hole from the top side of the false 
floor (Figure 25). 
 

 

Figure 25                                                      

P82.70-xxxx-71

 

7.  Snap the contact plate (A, Figure 26) into 

false floor by firmly pressing down from the 
top side until an audible click sounds. 

8.  Route the contact plate cabling through the 

cable managers (B, Figure 26) on the 
underside of the false floor. 

9.  Feed the male FAKRA and power supply 

connectors of the contact plate through the 
hole (C, Figure 26) inside the upper 
compartment, to the housing for the female 
FAKRA and power supply connectors at the 
outside bottom of the upper compartment. 

Note:

 The wiring harness for the Tele 

Aid/Roadside Assistance button assembly 
runs through the hole in the upper 
compartment. 

 

Figure 26                                                      

P82.70-xxxx-71

 

 

PRELIMINARY DRAFT

 November 2004

 

11

Summary of Contents for 171.456 2005
















Reviews:

No comments

Brands by name

Popular brands

Load more brands