background image

85-03-01145 

ML54 

Page 

32

 

 

Recommendations for Television Installation 

Note:

 The model depicted in the images is a representation of a Mendota Hearth fireplace. These recommendations apply to all 

Mendota Hearth Fireplaces. 

When planning to install a television or other heat sensitive product above your fireplace, there are some points to consider. 

Many television manufacturers specify in their installation instructions that the television must not be installed near or above a 
heat source. The decision to install a television near or above a Mendota fireplace rests solely on the consumer. It is the 
consumers responsibility to satisfy television specifications and insure the television will not exceed maximum operation 
temperatures. Mendota Hearth will not be held liable for any adverse effects on a television or other products located near to a 
Mendota Hearth fireplace. 

The drawings below show recommendations that may be used as a guide for those consumers that decide to locate a television 
above a Mendota Hearth fireplace. These recommendations have been found to reduce the heat impact to a television when 
installed above a Mendota Hearth fireplace.  

 

Recommendation 1: Add a mantel 

Add a mantel above the fireplace. The mantel shall be at least 2 inches deeper than the depth of the television, and at least as wide 
as the television. The mantel shall be mounted so that its top surface is a minimum of 18 inches above the top air gap of the 
fireplace. 

Attention:

 If the mantel is constructed of combustible materials, make certain that the entire mantel meets the clearances to 

combustible mantel requirements.  

 

 

Summary of Contents for ML54

































































































Reviews: