Mendota FULLVIEW AA-11-02591 Page 31 Installation And Operating Instruction Manual Download

Page: 31 / 80

85-03-00955

P a g e

EXTERIOR VENT LOCATIONS AND RESTRICTIONS

ALL MEASUREMENTS FROM CENTER-LINE OF VENT CAP

Vent Terminal

Air Supply Inlet

Area where terminal is

not permitted

A =

Clearance above grade, veranda, porch,
deck, or balcony (*12 inches (30 cm) mini-
mum). Vinyl surfaces require 24” min.

H = *Not to be installed above a meter/regulator as-

sembly within 3 feet (90 cm) horizontally from
the center-line of the regulator

B =

Clearance to window or door that may be
opened
(*12 inches (30 cm) minimum.

I =

*Clearance to service regulator vent outlet *3
feet (92 cm) minimum.

C =

*Clearance to permanently closed window
(minimum 12 inches (30 cm) recommended
to prevent condensation on window)

J =

*Clearance to non-mechanical air supply inlet to
building or the combustion air inlet to any other
appliance.
12 inches (30 cm) minimum.

D =

*Vertical clearance to ventilated soffit located
above the terminal from the center-line of the
terminal 18” (47 cm) min.

K = *Clearance to a mechanical air supply inlet 6

feet (1.8 m) minimum

E =

*Clearance to unventilated soffit 18” min (46
cm) min.

L =

†

Clearance above paved side-walk or a paved

driveway located on public property (*7 feet (2.1
m) minimum)

F =

Clearance to outside corner - 7 inches (18
cm).

M = Clearance under veranda, porch, deck, or bal-

cony (*12 inches (30 cm) minimum

‡

)

G =

Clearance to inside corner - 12 inches (30
cm). Vinyl surfaces require 24” min (60 cm).

Minimum 24” horizontal clearance to any sur-
face, such as an exterior surface, for vertical ter-
minations.

†

A vent shall not terminate directly above a sidewalk or paved driveway, which is located between two single-family dwell-

ings and serves both dwellings.

‡

Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.

* As specified in CGA B1:19 Installation Codes (1991).

Note

: Local codes or regulations may require different clearances.

Clearances are in accordance with local installation codes and the requirements of the gas supplier. Dégagement con-
forme aux codes d’installation locaux et aux exigences du foumisseunde gaz.

Summary of Contents for FULLVIEW AA-11-02591

















































































Search results

Summary of Contents for FULLVIEW AA-11-02591

Reviews:

Related manuals for FULLVIEW AA-11-02591

Brands by name

Popular brands

Mendota FULLVIEW AA-11-02591, Installation And Operating Instruction Manual

Search results

Summary of Contents for FULLVIEW AA-11-02591

Reviews:

Related manuals for FULLVIEW AA-11-02591

Brands by name

Popular brands