background image


 
 
 

SAFETY AND WARNING INFORMATION 

READ and UNDERSTAND

 all instructions carefully before starting

 the appliance. 

FAILURE TO

 

FOLLOW

 these instruc-

tions may result in a possible fire hazard and will void the warranty. 
 

Any safety screen or guard removed for servicing must be replaced before operating this appliance.

 Tout écran ou protecteur 

retiré pour permettre l’entretien de l’appareil doit être remis en place avant de mettre l’appareil en marche.

 

 

DO NOT USE 

this appliance if any part has been under water. Immediately 

CALL

 a qualified service technician to inspect 

the appliance and to replace any part of the control system and any gas control, which has been underwater. 
 

THIS UNIT IS NOT FOR USE WITH SOLID FUEL

 
Installation and repair should be 

PERFORMED

 by a qualified service person. The appliance and venting system should be 

INSPECTED

 before initial use and at least annually by a professional service person. More frequent cleaning may be re-

quired due to excessive lint from carpeting, bedding, material, etc. It is 

IMPERATIVE

 

that the unit’s control compartment, 

burners, and circulating air passageways 

ARE KEPT CLEAN

 to provide for adequate combustion and ventilation air. 

 
Always 

KEEP

 the appliance clear and free from combustible materials, gasoline, and other flammable vapors and liquids. 

 

NEVER  OBSTRUCT

  the  flow  of  combustion  and  ventilation  air.  Keep  the  front  of  the  appliance 

CLEAR

  of  all  obstacles 

and materials for servicing and proper operation. 
 
Due to high temperature, the appliance should be 

LOCATED

 out of traffic areas and away from furniture and draperies. 

En raison des températures élevées, l’appareil devrait être installé dans un endroit où il y a peu de circulation et loin du 
mobilier et des tentures. 
 
Clothing  or  flammable  material 

SHOULD  NOT  BE  PLACED

  on  or  near  the  appliance.  On  ne  devrait  pas  placer  de 

vêtements ni d’autres matières inflammables sur l’appareil ni à proximité. 
 
 
Young children should be 

CAREFULLY SUPERVISED

 when they are in the same room as the appliance. 

Toddlers, young 

children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk in dividuals in 
the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children and other at risk 
individuals out of the room and away from hot surfaces.  “Les jeunes enfants devraient être surveillés étroitement lorsqu’ils  se trouvent 
dans l

a même pièce que l’appareil. Les tout petits, les  jeunes enfants ou les adultes peuvent subir des brûlures s’ils viennent en con-

tact avec la surface chaude. Il est recommandé d’installer une barrière physique si des personnes à risques habitent la maiso n. Pour 
empêcher  l’accès  à  un  foyer  ou  à  un  poêle,  installez  une  barrière  de  sécurité;  cette  mesure  empêchera  les  tout  petits,  les  je unes 
enfants et toute autre personne à risque d’avoir accès à la pièce et aux surfaces chaudes.

 

 
 
Children  and  adults  should  be 

ALERTED

  to the  hazards  of  high  surface  temperature  and  should 

STAY  AWAY

 to avoid 

burns or clothing ignition. Young children should be 

CAREFULLY SUPERVISED

 when they are in the same room as the 

appliance. 
 
These units 

MUST

 use one of the vent systems described in the Installing Your Fireplace section of the Installers Guide. 

NO OTHER

 vent systems or components 

MAY BE USED

 
This gas fireplace and vent assembly 

MUST

 be vented directly to the outside and 

MUST NEVER

 be attached to a chimney 

serving  a  separate  solid  fuel-burning  appliance. Each  gas  appliance 

MUST  USE

  a  separate vent system. Common vent 

systems are 

PROHIBITED

 
If the vent-air intake system is disassembled for any reason, reinstall per the instructions provided for the initial installation. 
 
The vent system assembly for this fireplace must be periodically examined by a qualified service agency. 
 

INSPECT

  the  external  vent  cap  on  regular  basis  to  make  sure  that  no  debris  is  interfering  with the  airflow.    The  flow  of 

combustion and ventilation air not to be obstructed 
 
DO NOT abuse the glass door by striking the glass, slamming the door shut, etc. 

Summary of Contents for DXV-45 DT4 - LX
























































Reviews: