manualshive.com logo in svg

Memak Rota 507, Installation And User Manual

Share
Download
Memak Rota 507 Installation And User Manual Download Page 13

INSTALLATION AND USER MANUAL FOR BAKERY OVEN WITH ROTATING TROLLEY 

 I

13

 

ROTA810

ROTA609

DEPTH                ( A ) mm / inc

                            (A1) mm / inc

                            

2496

2960

2217

2680

WIDTH                ( B ) mm / inc

1950 

1711

HEIGHT               ( H ) mm / inc

                            (H1) mm / inc

2320

2590

2320

2595

PRODUCT COMMISSIONING 

• 

Installation is carried out by the manufacturer’s personnel or by the personnel authorized by the 

manufacturer.

• 

Manufacturer is not responsible for any failure caused by unauthorized personnel. Manufacturer 

is not responsible for any malfunctions caused by unauthorized personnel during the installation, 

despite the labor guarantee.

• 

Manufacturer cannot be held responsible for the place and technical and legal suitability of the 

machine.

• 

All operations must be carried out in accordance with the directives of a sole authorized person.

• 

Operators and people under their command must wear protective clothing in compliance with 

the operation. 

Manufacturer is not liable for accidents, damage and machine failures caused by the failure to comply 

with the rules in this section.

General Rules on Unpacking the Machine

• 

Inspect the machine for damages during transportation before unpacking. Check that all parts 

listed in the shipping documents are present. If there are missing parts, manufacturer must be 

informed within 24 hours.

• 

Dispose of the packaging material in accordance with the applicable legal regulations  when the 

machine is fully installed.

• 

Store the materials used for lifting the machine in a suitable place for future use. (Figure 2 and 

Figure 3)

Summary of Contents for Rota 507

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands