background image

M-WRG-K  

Installation manual 

M-WRG-S 
 

 

Meltem Wärmerückgewinnung GmbH & Co.KG 

Am Hartholz 4     D-82239 Alling     [email protected]     www.meltem.com

  

Important user information

   

Ventilation with heat recovery

 

With the decentralized ventilation system M-WRG with 
heat recovery from Meltem you have acquired a high 
quality product. This ventilation system serves you as 
an improvement for your home and your health as well 
as  a  protective  measure  against  moisture  and  mold 
damages in your home. 
 
Ventilation by opening windows, especially during cold 
seasons, belongs to the past. From now on, fresh and 
filtered air is supplied fully automated. The stale air is 
extracted  and  its  warmth  transferred  to  the  fresh  air, 
via the heat exchanger.  While doing so, the M-WRG 
ventilation  units  have  minimum  power  consumption. 
You  save  heating  costs,  increase  the  comfort  of  your 
home and at the same time reduce the impact on the 
environment by reducing CO2 emissions. 
Of  course  you  still  may  open  your  windows  - 
especially during warmer days. 
 
A  family  of  four  produces  daily  an  average  of  10-14 
liters  of  moisture,  due  to  cooking,  laundry,  personal 
hygiene,  and  breathing  of  inhabitants,  plants  and 
animals!  This  excessive  amount  of  moisture,  within 
the  interior  air,  is  extracted  through  the  M-WRG 
ventilation  unit  and  therefore  prevents  the  forming  of 
mold and resulting damages in the building structure. 
At  the  same  time,  fumes  from  floors,  furniture  and  a 
too high CO2 concentration in the air, which can lead 
to fatigue and health issues, will be extracted from the 
interior rooms and replaced by fresh and clean air.  

 

Directions for correct usage  

Please  read  this  manual  carefully  and  follow  the 
instructions  contained  in  this  manual.  Additionally, 
familiarize yourself with the operations of the M-WRG 
ventilation unit, as well as please pay attention to the 
warnings and cautions contained in this manual. 
 

  Never operate the M-WRG ventilation unit without 

filters.  Only  with  the  original  filters  from  Meltem, 
the  units  will  remain  clean,  fully  operative,  and 
have a long lifespan. 

 

  The M-WRG ventilation unit may only be operated 

once installed correctly. 

 

  When  ventilating  basements  or  similar  rooms  we 

advise  to  be  cautious  (especially  during  the 
summer  season  and  warm  weather),  due  to  the 
fact  that  the  moisture  in  the  air  will  condense  on 
cold  interior  walls  and  -  despite  ventilation  - 
moisture  damages  can  occur.  Therefore,  please 
only  ventilate  at  night  during  warm  weather 
seasons! If you would like to ventilate such rooms 
with an M-WRG ventilation system, please consult 
with the manufacturer prior to purchase. 

 
 
 
 

  Never cover the M-WRG ventilation unit or any part 

of  it  with  e.g.  cabinets,  blinds  or  curtains.  A 
minimum  distance  of  30  cm  to  any  furniture  is 
required, in order for the M-WRG ventilation unit to 
remain fully operable. 

 

  The M-WRG ventilation unit has been designed for 

continuous  operation  and  a  long  lifespan.  During 
cold  seasons,  the  M-WRG  ventilation  unit  should 
be  operated  continuously.  The  energy  saving 
motors  and  innovative  electronics  guarantee  – 
despite  continuous  operation-  for  a  low  power 
consumption  (approx.  3.8  Watt  at  level  1).  Only  a 
continuous  operation  achieves  a  permanent 
extraction  of  moisture  and  condensation.  If  this 
does  not  occur,  it  is  possible  that  condensate  will 
gather in the unit. 

 

  If  a  high  concentration  of  moisture  occurs,  we 

recommend  regularly  ventilating  the  room  at  the 
highest ventilation level for 10 minutes, in order to 
eliminate  any  possible  condensation  inside  the 
unit. 

 

 

In  order  to  guarantee  a  smooth  operation, 
especially  during  low  exterior  temperatures 
(below  -5°C),  you  should  avoid  interior 
temperatures below 15°C. 

 
Caution:  In  case  of  exterior  temperatures  below 
0°C, icicles may form at the façade covers. These 
should be removed for safety purposes. 

 

Maintenance and Filter replacement 

The  unit  automatically  monitors  the  filter  status.  An 
acoustic  warning  signal  will  inform  you,  when  the 
filters need to be replaced.

 

  

However,  for  hygienic  reasons,  it  is  strongly 
recommended  to  replace  the  filters  at  least  once 
per year, ideally before the heating season.

 

For  a  reliable  operation  of  the  units  and  for  your 
own  safety,  only  original  and  certified  parts  from 
Meltem  should  be  used.  Otherwise  this  may  void 
the warranty and Meltem will not be liable for any 
damages.  
 

We  hope  you  will  enjoy  your  new  M-WRG  home 
ventilation system with heat recovery!

 

 
 
 

 

 

Summary of Contents for M-WRG-K
















Reviews: