Meltem M-WRG-II Installation Manual Download Page 4

Page: 4 / 48

Installation manual

M-WRG-II ventilation units

- 4 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

11.6

Fixing the ventilation unit .............................................................................................. 36

11.6.1 Surface-mount installation ............................................................................................ 36

11.6.2 Flush-mount installation ................................................................................................ 36

11.6.3 Flush-mount installation with ductwork connection ....................................................... 37

11.6.4 U

integrated into wall installation ................................................................................ 39

11.7

Connecting the mains cable and control cable (if used) ............................................... 40

11.8

Connecting the M-WRG-II O/EGG-AUS option ............................................................ 41

11.9

Fixing the electronics compartment cover plate ........................................................... 41

11.10

Attaching the unit cover pull-out straps (for U

integrated into wall installation only) .... 42

11.11

Attaching the unit cover to the ventilation unit .............................................................. 42

11.12

Attaching the U

cover plate (for U

integrated into wall installation only) ..................... 43

11.13

Connecting flat ducts to the ventilation unit (for surface-mount installation with

ductwork connection only) ............................................................................................ 43

11.14

Attaching the cover to the duct adapter (for flush-mount installation with ductwork

connection only) ............................................................................................................ 44

11.15

Starting up the ventilation unit ...................................................................................... 44

Summary of Contents for M-WRG-II

















































Search results

Summary of Contents for M-WRG-II

Reviews:

Brands by name

Popular brands

Meltem M-WRG-II, Installation Manual

Search results

Summary of Contents for M-WRG-II

Reviews:

Brands by name

Popular brands