Meltem M-WRG-II Installation Manual Download Page 20

Page: 20 / 48

Installation manual

M-WRG-II ventilation units

- 20 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

6.2

Installation materials required

Additional installation materials are needed for surface-mount, flush-mount with ductwork

connection and U

integrated into wall installation. These must be ordered separately.

6.2.1 Surface-mount installation for units from the M-WRG-II P series

Type

Part no. Description

M-WRG-II M/AP-KA 735004 Surface-mount installation kit consisting of drilling

templates for unit and outer wall terminal stainless

steel pod, including outdoor air and exhaust air pipe

DN 100, 2 x 0.5 m, exhaust air pipe with 1/2” male

thread condensate connection

M-WRG-II KA

731000 For surface-mount installation with ductwork connec-

tion only:
Duct adapter for ductwork connection to another room

when running surface-mount flat ductwork, for surface-

mount units, connection via fitting with sleeve or flat

ductwork bracket M-WRG-FK-W

6.2.2 Surface-mount installation for units from the M-WRG-II E series

Type

Part no. Description

M-WRG-II M/AP

735002 Surface-mount installation kit consisting of drilling

templates for unit and outer wall terminal stainless

steel pod, including outdoor air and exhaust air pipe

DN 100, 2 x 0.5 m

M-WRG-II KA

731000 For surface-mount installation with ductwork connec-

tion only:
Duct adapter for ductwork connection to another room

when running surface-mount flat ductwork, for surface-

mount units, connection via fitting with sleeve or flat

ductwork bracket M-WRG-FK-W

6.2.3 Flush-mount installation with ductwork connection

Type

Part no. Description

M-WRG-II KA-UP

731002

Duct adapter for flush-mount M-WRG-II units, one or

two ductwork connections possible, for flush-mounting

flat ductwork or flexible pipe

6.2.4 U

integrated into wall installation

Type

Part no. Description

M-WRG-II U

731001 U

adapter kit, needed to install the M-WRG-II units in

the U

installation kit

M-WRG-II U

AD/WS 735100 U

cover

Summary of Contents for M-WRG-II

















































Search results

Summary of Contents for M-WRG-II

Reviews:

Related manuals for M-WRG-II

Brands by name

Popular brands

Meltem M-WRG-II, Installation Manual

Search results

Summary of Contents for M-WRG-II

Reviews:

Related manuals for M-WRG-II

Brands by name

Popular brands