manualshive.com logo in svg

Meinberg M900, Operating Instructions Manual, Page: 36 / 170

Share
Download
Meinberg M900 Operating Instructions Manual Download Page 36

Set GPS Receiver Simulation Mode

Enabling this menu lets the user run the LANTIME without antenna. Normally the

NTPD loses synchronization with the GPS when the antenna is disconnected or the
GPS did not receive enough satellites (red FAIL LED is turned on). When IGNORE
LOCK is enabled the status information from the GPS is fixed to SYNC. So it is
possible to set the NTPD with any other time entered by the SETUP INITIAL TIME
menu. Usually this menu should be disabled. If this option is enabled an "*" will be
shown behind the time string in the root menu.

Menu: Init GPS

Initiate Cold Boot of GPS Receiver

This menu lets the user initialize all GPS data, i.e. all saved satellite data will be

cleared. The user has to acknowledge this menu again before the initialization starts.
The system starts operating in the COLD BOOT mode and seeks for a satellite to read
its actual parameters.

36

   Setup GPS

       

 

 Antenna Length

>Simulation Mod<
 Init GPS

  

SET GPS RECEIVER
SIMULATION MODE

    disabled

   Setup GPS

       
 

 Antenna Length

 Simulation Mode
>Init GPS      <

  

> GPS COLD BOOT<

  GPS WARM BOOT
  Set Position
  Set GPS Time

   INITIATE

       

 

   COLD BOOT

 OF GPS RECEIVER
   Press F2

  

> GPS COLD BOOT<
  GPS WARM BOOT
  Set Position

  Set GPS Time

Summary of Contents for M900











































































































































































Reviews:

No comments