Meinberg M900 Operating Instructions Manual Download Page 30 | Manualshive

Page: 30 / 170

Meinberg M900 Operating Instructions Manual Download Page 30

Configuration User Interface

There are several ways to configure the LANTIME parameters:

Command Line Interface (CLI) via TELNET
Command Line Interface via SSH
Command Line Interface via serial terminal in front panel (38400/8N1/VT100)
HTTP Interface
Secure HTTP Interface (HTTPS)
Front panel LCD Interface
SNMP Management

To put LANTIME into operation for the first time an IP address is entered via the
front   panel   keys   and   LC   display   (refer   to:   DHCP   IPv4   or   AUTOCONF   IPv6).
LANTIME   variants   with   serial   terminal   connector   in   the   front   panel   can   be
configured via serial terminal (38400Baud/8N1/VT100) can be configured via the
serial interface in the front panel, running a terminal software e.g. on a laptop. If once
the   IPv4   address,   netmask   and   IPv4   GATEWAY  are  configured,   or   the  network
interface is initialized by IPv6 SCOPE-LINK, the LANTIME is accessible from any
computer in the network (remote).

To set up a TELNET connection the following commands are entered:

telnet 198.168.10.10

//

LANTIME IP address

user: root
password: timeserver

With “setup” the configuration program is started.

To set up a SSH connection the following commands are entered:

ssh [email protected] //

LANTIME IP address

password: timeserver

With “setup” the configuration program is started.

To set up a HTTP connection the following address is to enter in a web browser:

http://198.168.10.10

//

LANTIME IP address

password: timeserver

To set up a Secure HTTP (HTTPS) connection the following address is entered in a
web browser:

https://198.168.10.10

//

LANTIME IP address

password: timeserver

30

«
...
28
29
30
31
32
...
»

Summary of Contents for M900











































































































































































Reviews:

No comments