Meinberg M900 Operating Instructions Manual Download Page 148

Page: 148 / 170

Outputs

The module GPS167-TC provides modulated and unmodulated (DC-Level Shift)

outputs. The format of the timecodes is illustrated in the diagramms "IRIG-" and
"AFNOR standard-format".

AM - Sine Wave Output

The amplitude-modulated carrier is available at the VG-connector pin 14a. The

carrier frequency depends on the code and has a value of 1 kHz (IRIG-B). The signal
amplitude is 3 V

(MARK) and 1 V

(SPACE) into 50

Ω

. The encoding is made by

the number of MARK-amplitudes during ten carrier waves. The following agreements
are valid:

a) binary "0":

2 MARK-amplitudes, 8 SPACE-amplitudes

b) binary "1":

5 MARK-amplitudes, 5 SPACE-amplitudes

c) position-identifier:

8 MARK-amplitudes, 2 SPACE-amplitudes

PWM DC Output

The pulse width modulated DC signals shown in the diagramms "IRIG" and

"AFNOR standard format" are coexistent to the modulated output and is available at
the VG connector pin 13a with TTL level.

Technical Data

OUTPUTS:

Unbalanced AM-sine wave-signal:
3 V

(MARK) / 1 V

(SPACE) into 50

Ω

PWM signal: TTL, high and low active

148

Summary of Contents for M900











































































































































































Search results

Summary of Contents for M900

Reviews:

Meinberg M900, Operating Instructions Manual, Page: 148 / 170

Search results

Summary of Contents for M900

Reviews: