background image

furnished under this warranty are subject to the same terms and conditions of the original 
warranty. This warranty supersedes any other warranty and is subject to the following 
terms and conditions: 
                        

WARRANTY 

Warranty of Meiji Techno products extends to the original purchaser of the 
product and is not transferable. 
                     

WARRANTY DURATION 

Meiji Techno

 

warrants this product against defects in material and/or 

workmanship for the life of the product from the date of original purchase to the 
original purchaser. The electrical warranty is limited to one year.  
                        

OWNER’S REGISTRATION CARD 

Return of the owner’s registration card by the original purchaser within ten (10) 
days after the original purchase is a condition precedent to coverage under this 
warranty. Meiji Techno

 

will at its option accept written proof of purchase from the 

original owner in lieu of a product registration card. 
                        

EXCLUSIONS AND LIMITATIONS 

Specifically excluded from this warranty are failures caused by abuse, neglect, 
misuse, improper operation, normal wear, accident, improper maintenance or 
modifications of ANY type. This warranty does not cover repair or replacement 
where normal use has exhausted the life of a part, product or instrument. All 
mechanical devices need periodic parts replacement and service to perform well. 
Service life of a product is dependent upon the care it receives and the 
conditions under which it has to operate. In no event shall Meiji Techno be liable 
for incidental or consequential damages. 
                                              

 
 
 
 
 
 
SERVICE
 

To obtain service under this warranty, please contact Meiji Techno

 

directly

 

and 

ask for the Product Service Department. State the nature of the problem, model 
and serial number of the product, date of purchase and location and name of the 
distributor the instrument was purchased from. After verification of warranty 
registration, Meiji Techno will issue a return authorization number. Customer may 
then return the product postage prepaid and insured to the authorized repair 
facility.  

 

In most instances, requests for warranty service will be performed in a prompt 
and routine manner and merchandise will be returned in a reasonable period of 

Summary of Contents for FL-LHJ



























Reviews: