Megger TTR20 Instruction Manual Download

Page: 47 / 60

AVTMTTR20 Rev 4 Dec 2015

Appendix B

ORDERING INFORMATION & SPARE PARTS LIST

Ordering Information

Item Cat.

No.

TTR20-1 Transformer Turns Ratio Test Set

TTR20-1

Included Accessories

Combined test leads set, "X/H" winding, 6 ft (1.8 m)

2007-713-6

Instruction manual

AVTMTTR20

Optional Accessories

Test Leads - TTR20-1 (Metal Connectors)

Combined test leads set, "X/H" winding, 12 ft (3.6 m)

2007-713-12

Combined test leads set, "X/H" winding, 20 ft,(6.1 m)

2007-713-20

Combined test leads set, "X/H" winding, 33 ft,(10.1 m)

2007-713-33

Test Leads - TTR20 (Discontinued)

TTR20 Lead Set, 1.8 m (6 ft)

35938

TTR20 Lead Set, 3.6 m (12 ft)

35942

TTR20 Lead Set, 6 m (20 ft)

36013

TTR20 Lead Set, 10 m (33 ft)

36042

Printer package including battery/line power serial thermal printer
with paper, battery pack and charger, printer interface cable, 120V
60Hz

35755-1

Semi-hard fabric transport case

35788

Summary of Contents for TTR20





























































Search results

Summary of Contents for TTR20

Reviews:

Related manuals for TTR20

Brands by name

Popular brands

Megger TTR20, Instruction Manual

Search results

Summary of Contents for TTR20

Reviews:

Related manuals for TTR20

Brands by name

Popular brands