Megger TTR20 Instruction Manual Download Page 13 | Manualshive

Page: 13 / 60

background image

INTRODUCTION

AVTMTTR20 Rev 4 Dec 2015

5

Upon Receipt of the TTR20

Check the equipment received against the packing list to ensure that all materials
are present. Notify Megger of any shortage. Telephone 610-676-8500.

Examine the instrument for damage received in transit. If any damage is
discovered, file a claim with the carrier at once and notify Megger or its nearest
authorized sales representative, giving a detailed description of the damage.

This instrument has been thoroughly tested and inspected to meet rigid
specifications before being shipped. It is ready for use when set up as indicated
in this manual.

Safety First

Be sure to read the safety information in Chapter 2 thoroughly and observe all
safety precautions and recommendations.

How to Use This Manual

Typographic Conventions

G

CAUTION

Cautions alert you to possible damage to equipment.

F

WARNING

Warnings alert you to conditions that are potentially
hazardous to people.

NOTE:

Notes provide important information.

«
...
11
12
13
14
15
...
»

Summary of Contents for TTR20





























































Reviews:

No comments

Related manuals for TTR20

Brand: Bartscher Pages: 22

Brand: Keithley Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: Campden instruments Pages: 8

Brand: NORLUX Pages: 2

Brand: Bahco Pages: 9

Brand: Farmi Forest Corporation Pages: 32

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Brand: Yamaha Pages: 48

Brand: Twiflex Pages: 5

Aqua Timer 3000

Brand: Melnor Pages: 6

Brand: Stone Pages: 36

Brand: Scilogex Pages: 21

Brand: BSi Pages: 2

Brand: Kellfri Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands