Megger TTR20 Instruction Manual Download Page 37 | Manualshive

Page: 37 / 60

background image

Maintenance and Troubleshooting

AVTMTTR20 Rev 4 Dec 2015

29

Battery Replacement

TTR20 test set is powered up from six AA-size replaceable alkaline batteries. A
battery holder (contained six batteries) is installed in a battery compartment on
the back side of the instrument housing. The compartment door is fixed to the
housing by two screws.

To replace the batteries proceed as follows:
1.  Remove the battery compartment door.
2.  Lift up a battery holder from the compartment. Unplug a battery strap.
3.  Replace all six batteries by the new ones. Use AA-size replaceable alkaline

batteries only. Observe the proper polarity of the batteries. A negative battery
terminal (flat bottom portion of battery) should be placed against a battery
holder spring. The batteries should be installed in series. See a battery holder
for proper polarity and battery installation orientation.

4. Connect a battery strap back to the battery holder. Install the battery holder

into the compartment.

5. Replace the battery compartment door and secure it with screws.
6. Turn on TTR20. It should display the opening screen, then the battery level

screen. The battery level displayed depends on many factors including type of
battery installed, battery manufacturing date, battery storing conditions, etc. In
average, the new battery level displayed should be above 80 %.

NOTE: The TTR20 is delivered with 6 standard "AA" batteries

(IEC LR-6) alkaline batteries installed. The specified
operating time of 12 hours is based on using these high-
capacity batteries or equivalent.

«
...
35
36
37
38
39
...
»

Summary of Contents for TTR20





























































Reviews:

No comments

Related manuals for TTR20

Brand: Raymarine Pages: 464

Brand: 3M Pages: 8

Brand: ZOLL Pages: 3

Brand: Gardena Pages: 13

Brand: Ecco Pages: 9

Brand: Talet Equipment Pages: 17

Brand: ACDC Pages: 4

LOUDEN 200 Series

Brand: ACCO Brands Pages: 144

Brand: B&K Pages: 16

Brand: B&G Pages: 2

Brand: Bang & Olufsen Pages: 2

Brand: Ocmis Irrigazione Pages: 100

Brand: Gaspardo Pages: 196

Brand: RAB Pages: 2

Heart Guardian AED

Brand: Radian Pages: 36

UltraVent XS Plus 6 2/3 E

Brand: Rational Pages: 220

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands