MegaPoints Controllers AutoSignal User Manual Download | Manualshive

Page: 2 / 16

background image

MegaPoints Controllers AutoSignal User Guide

Revision 10

megapointscontrollers.co.uk

Page 2

Contents

AutoSignal - Colour light signal controller .............................................................................................. 3

Introduction ........................................................................................................................................ 3
First use ............................................................................................................................................... 4

Timer operation ...................................................................................................................................... 4

Hook-up Options ................................................................................................................................. 6
Sensors ................................................................................................................................................ 7

DCC Occupancy sensor .................................................................................................................... 7
DCC Points Position sensor ............................................................................................................. 7
Infra-Red sensor .............................................................................................................................. 8
Switches .......................................................................................................................................... 9
Diverging route hook-up ................................................................................................................. 9

Selectable modes .............................................................................................................................. 10

Linking units .......................................................................................................................................... 13
Feather switch ....................................................................................................................................... 14
Danger switch / sensor ......................................................................................................................... 15
Complimentary products ...................................................................................................................... 15
References ............................................................................................................................................ 16
Contacting us ........................................................................................................................................ 16

«
1
2
3
4
...
»

Summary of Contents for AutoSignal

















Reviews:

No comments

Related manuals for AutoSignal

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: NEC Pages: 149

Brand: NEC Pages: 13

Brand: Baby Jogger Pages: 16

Brand: Samson Pages: 40

Brand: HANYOUNG NUX Pages: 56

Brand: Koer Pages: 6

Brand: Dantherm Pages: 20

GRASS VALLEY MDX-3901

Brand: Belden Pages: 45

Brand: BabyActive Pages: 4

Brand: Yolink Pages: 23

TRIO MPC-165 Series

Brand: Sutter Instrument Pages: 60

Brand: Sielco Elettronica Pages: 15

Brand: ICP DAS USA Pages: 4

InRAX MVI46-PDPS

Brand: ProSoft Technology Pages: 72

Verifi FingerTouch Security

Brand: Zvetco Biometrics Pages: 8

Neon 2000 Family

Brand: UniData Communication Systems Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands