background image

16

7. Operation

1. Cabinet Cooler

 

The Cabinet Cooler is factory set to deliver the most efficient cooling needed to 

maintain a desired temperature inside an enclosure. 

At 80psi (5.5 Bar), 10cfm (70% of 15 cfm, red generator) of cold air will exit from the 

Cabinet Cooler providing 293 Watts (1,000 Btu) of Cooling. 

The bladder valve acts as a pressure relief valve. This will automatically release air 
from the enclosure maintaining approximately 8” water column (0.0199 Bar) positive 
pressure inside the cabinet/panel. 

2. Generators

 

The generators within the Cabinet Cooler control the air consumption and air flow. They 
also influence the achievable temperatures. 

The chart below shows achievable temperatures with different generators fitted. 

Please note these are approximate temperatures and should only be used as a guide. 
The Cabinet Cooler will perform differently when used in other environments.

 

Inlet air pressure 

Product 

Code 

Generator 

Colour 

Consumption 

in CFM (l/min)

60 PSI (4.1 Bar)

80 PSI (5.5 Bar)

100 PSI (6.8 Bar)

CFM at 

test

2.5 turns of 

needle valve 

CFM at 

test

2.5 turns of 

needle valve 

CFM at 

test

2.5 turns of 

needle valve 

cfm (l/min)

°C

cfm (l/min)

°C

cfm (l/min)

°C

A21008

Green

8L (227)

15 (425)

-23.4

19 (538)

-30.1

21 (595)

-33.4

A20008

Yellow

8H (227)

13 (368)

-24.2

18 (510)

-28.5

20 (566)

-31.7

A21010

Green

10L (283)

15 (425)

-26.9

19 (538)

-35.5

21 (595)

-36.0

A20010

Yellow

10H (283)

13 (368)

-27.2

18 (510)

-35.0

21 (595)

-31.3

A21015

 

15L (425)

17 (481)

-29.8

22 (623)

-34.2

25 (708)

-35.4

A20015

Red

15H (425)

16 (453)

-28.3

21 (595)

-32.9

25 (708)

-32.6

A21025

Grey

25L (708)

23 (651)

-23.3

28 (793)

-23.7

30 (849)

-25.7

A20025

Blue

25H (708)

23 (651)

-19.0

30 (849)

-23.4

31 (878)

-24.9

A21035

Beige

35L (991)

27 (765)

-16.7

34 (963)

-16.5

39 (1104)

-18.6

A20035

Brown

 

35H (991)

30 (849)

-15.8

36 (1019)

-18.6

43 (1218)

-18.0

Summary of Contents for A70000

























Reviews: