background image

22

Electromagnetic Compatability

8.7

8

Electromagnetic Capability

Troubleshooting & technical information

 The medi pcs requires special precautions regarding EMC and needs to be installed and put into service according to the EMC 

information provided in these accompanying documents.

WARNING: Portable RF communications equipment (including peripherals such as antenna cables and external antennas) 

should be used no closer than 30 cm (12 inches) to any part of the medi pcs, including cables specified by the manufacturer.  

Otherwise, degradation of the performance of this equipment could result.

WARNING: A risk of increased emissions or decreased immunity may result if any additional cables are attached.

WARNING: Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in 

improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are 

operating normally.

WARNING: Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this 

equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and 

result in improper operation.

1

2

3

Emissions Test

Compliance

Electromagnetic Environment - Guidance

4

RF emissions

CISPR 11

Group 1

The medi pcs uses RF energy only for its internal function.  There-

fore, its RF emissions are very low and are no likely to cause any 

interference in nearby electronic equipment.

6

RF emissions

CISPR 11

Class B 

7

Harmonic emissions

IEC 61000-3-2

Class A

Voltage Fluctuations 

 IEC 61000-3-3

Complies 

Guidance and Manufacturer’s Declaration – Electromagnetic Emissions

The medi pcs is intended for use in the electromagnetic environment specified 

below.  The customer or the user of the medi pcs should assure that it is used in 

such an environment.

The medi pcs is suitable for use in all establishments, including 

domestic establishments and those directly connected to the 

public low-voltage power supply network that supplies buildings 

used for domestic purposes.

Summary of Contents for Pcs brio





























Reviews: