Med-Mizer ActiveCare-Standard User Manual Download Page 15 | Manualshive

Page: 15 / 33

background image

ActiveCare - Standard

User Manual

MAN-ActiveCare REV03

ActiveCare Standard USER MANUAL

Page 15 of 33

3.

Install high/low weldments to the frame using the bolts and nuts provided. The high/low
assembly bosses must go on top of the frame bosses.

4.

Hand tighten nuts to each bolt and fasten firmly using the 5/8” ratchet/impact and 5/8”
wrench.

High/Low weldment

mounted on top of

frame boss.

Hand tighten nut

Firmly fasten nuts

and bolts together

«
...
13
14
15
16
17
...
»

Summary of Contents for ActiveCare-Standard


































Reviews:

No comments

Related manuals for ActiveCare-Standard

Brand: Parker Pages: 54

Brand: Harken Pages: 4

Brand: Zetec Pages: 23

Brand: NEC Pages: 44

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: Laserworld Pages: 8

Brand: Laserworld Pages: 6

Brand: LaserLiner Pages: 56

Brand: LaserLiner Pages: 54

Brand: MacDon Pages: 2

Brand: PacBio Pages: 13

Brand: Pablo Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands