MDT Technologies KNX SCN-RT1UPE.01 Technical Manual Download Page 55 | Manualshive

Page: 55 / 56

MDT Technologies KNX SCN-RT1UPE.01 Technical Manual Download Page 55

MDT RTC

N

MDT Room Temperature Controller flush mounted 1-fold
MDT Room Temperature Controller surface mounted 1-fold

Version
SCN-RT1UP.01

Room Temperature Controller 1-fold

flush mounted, white, 55mm

SCN-TS1UP.01

Room Temperature Sensor 1-fold

flush mounted, white, 55mm

SCN-RT1UPE.01

Room Temperature Controller 1-fach with adjustment knob flush mounted, white, 55mm

SCN-RT1APE.01

Room Temperature Controller 1-fach with adjustment knob surface mounted, white

SCN-RT1UP.01

• Fits all switches with 55mm rocker:

- BERKER S1, B1, B3, B7
- GIRA Standard 55, E2, Event, Esprit
- JUNG A500, Aplus

- MERTEN M-Smart, M-Arc, M-Plan

• Integrated temperature controller (PI,Two-position, PWM)
• For indoor temperature controlling, range -10° to +50°
• Limit values min/max, Frost protection alarm,

Memory for min/max
• Desired value can be given by visualisation,

e.g. MDT VisuControl
• Day-, night- and frost protection operation
• HVAC object and 1bit object to choose operation mode
• RHCC status and bit/byte objects to declare status
• Installation with enclosed support ring,

integrated bus coupling unit
• 3 years warranty

SCN-TS1UP.01

SCN-RT1UPE.01

SCN-RT1APE.01

The MDT Room Temperature Controller is used to control the indoor temperature, it has a working range from -10 to +50°C.

The Room Temperature Controller detects the temperature and releases telegrams in dependence on its parameterisation.
The characteristic of the Temperature Controller (Two-position, PI and PWM control) can be set in the ETS3/4. The

controller stores the minimum and maximum temperature and releases an alarm telegram if the temperature differs from the
programmed limit values. The temperature of the frost protection is parameterizable.

Fits all switches with 55mm rocker:

•  BERKER S1, B1, B3, B7 glass
•  GIRA Standard 55, E2, Event, Esprit
•  JUNG A500, Aplus
•  MERTEN M-Smart, M-Arc, M-Plan

The MDT Room Temperature Controller is a flush mounted device for fixed installations in dry rooms, it is delivered with
support ring. For project design and commissioning of the MDT Room Temperature Controller it is recommended to use the

ETS3f/ETS4 or later. Please download the application software at www.mdt.de\downloads.

• production in Germany, certified according to ISO 9001
• modern design
• fully compatible to all KNX/EIB devices

MDT technologies GmbH

•

51766 Engelskirchen

•

Papiermühle 1

Tel.: + 49 - 2263 - 880

•

Fax: + 49 - 2263 - 4588

•

[email protected]

•

www.mdt.de

Stand: 1011

DIN EN ISO 9001

TAW Cert

Zert.Nr.1905606

«
...
53
54
55
56
»

Summary of Contents for KNX SCN-RT1UPE.01

























































Reviews:

No comments