manualshive.com logo in svg

MDT Technologies KNX SCN-RT1UPE.01, Technical Manual, Page: 5 / 56

Share
Download
MDT Technologies KNX SCN-RT1UPE.01 Technical Manual Download Page 5

 

 

Technical

 

Manual

 

Room

 

Temperature

 

Controller

 

SCN

‐

RT1

 

 

 

MDT technologies GmbH  •  

51766 Engelskirchen  •  Papiermühle 1

 

 

Tel.: +49-2263-880  •  Fax: +49-2263-4588  • [email protected]  •  www.mdt.de 

5

 

 

2.3

 

Exemplary

 

circuit

 

diagram

 

 

 

 

 

Illustration

 

1:

 

Exemplary

 

circuit

 

diagram

  

 

2.4

 

Structure

 

&

 

Handling

 

 

The

 

room

 

temperature

 

controller

 

is

 

available

 

in

 

three

 

different

 

designs.

 

There

 

are

 

designs

 

for

 

flush

‐

mounting

 

and

 

surface

‐

mounting.

  

All

 

of

 

the

 

devices

 

contain

 

of

 

a

 

bus

‐

connection,

 

a

 

programming

 

button

 

and

 

a

 

programming

 

LED

 

at

 

the

 

back.

 

     

     

 

Illustration

 

2:

 

Temp.

‐

Controller

   

 

Illustration

 

3:

 

Temp.

‐

Controller

     

Illustration

 

4:

 

Temp.

‐

Controller

  

flush

‐

mounted

   

 

 

      

surface

‐

mounted

   

 

       

flush

‐

mounted

 

SCN

‐

RT1UP.01

   

 

 

      

SCN

‐

RT1APE.01

   

 

       

SCN

‐

RT1UPD.01

 

 
 

The

 

room

 

temperature

 

sensor,

 

SCN

‐

TS1UP.01,

 

is

 

for

 

flush

‐

mounting.

 

It

 

contains

 

also

 

of

 

a

 

bus

‐

connection,

 

a

 

programming

 

button

 

and

 

a

 

programming

 

LED.

 

 

 

 

Summary of Contents for KNX SCN-RT1UPE.01

























































Reviews:

No comments