MDT Technologies BE-BZS86.01 Technical Manual Download Page 158

Page: 158 / 164

Technical Manual

–

Central Operation Unit Smart

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Phone: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

158

5 Index

5.1 Register of illustrations

Figure 1: Exemplary circuit diagram

..................................................................................................... 10

Figure 2: Structure & Handling

............................................................................................................. 10

Figure 3: General settings

...................................................................................................................... 19

Figure 4: Time and Astro settings

......................................................................................................... 20

Figure 5: Advanced sunrise/sunset settings

........................................................................................... 21

Figure 6: Settings - Display appearance

................................................................................................ 22

Figure 7: Settings - Adaption to ambience

............................................................................................ 23

Figure 8: Settings - User defined colours

.............................................................................................. 26

Figure 9: Settings - Info and Standby display

....................................................................................... 27

Figure 10: Settings - State values 1-3

.................................................................................................... 30

Figure 11: Settings - Messages and Alarms

.......................................................................................... 31

Figure 12: Settings - Functional Level

.................................................................................................. 34

Figure 13: PIN Code - Alarm system control

........................................................................................ 35

Figure 14: PIN Code - Device lock

....................................................................................................... 36

Figure 15: PIN Code - Button function with PIN Code

........................................................................ 37

Figure 16: PIN Code – Lock changing the time switch

........................................................................ 38

Figure 17: Settings - Logic

.................................................................................................................... 40

Figure 18: Settings - Temperature measurement

................................................................................... 41

Figure 19: Settings - Temperature Controller

....................................................................................... 45

Figure 20: Example - Dead zone and corresponding setpoints

............................................................. 56

Figure 21: Settings - Flow temperature limit

........................................................................................ 57

Figure 22: Settings - PI control continuous

........................................................................................... 59

Figure 23: Settings - PI control switching (PWM)

................................................................................ 61

Figure 24: Settings - 2-step control (switching)

.................................................................................... 63

Figure 25: Additional settings - Heating and Cooling

........................................................................... 65

Figure 26: Settings - Step switch bit coded

........................................................................................... 67

Figure 27: Switching behaviour - Step controller

................................................................................. 70

Figure 28: Setting - Manual control only

.............................................................................................. 71

Figure 29: Ventilation control - Behaviour at Init

................................................................................. 72

Figure 30: Ventilation control - Sticking protection

............................................................................. 72

Figure 31: Ventilation control - Priority

................................................................................................ 72

Figure 32: Ventilation control - Status object

....................................................................................... 73

Figure 33: Example - Output: Step switch as Byte

............................................................................... 74

Figure 34: Settings - Mode Selection

.................................................................................................... 76

Figure 35: Settings - Presentation of Operating modes

......................................................................... 78

Figure 36: Settings - Temperature Shift

................................................................................................ 79

Figure 37: Settings - Presentation of Temperature shift

........................................................................ 79

Figure 38: Setting - Heating/Cooling switchover

.................................................................................. 80

Figure 39: Setting - Presentation of Heating/Cooling switchover

......................................................... 80

Figure 40: Settings - Ventilation control levels

..................................................................................... 81

Figure 41: Presentation - Ventilation control levels

.............................................................................. 82

Figure 42: Settings - Ventilation control auto/manual

.......................................................................... 83

Figure 43: Presentation - Ventilation control auto/manual

................................................................... 83

Figure 44: Settings - Direct buttons: Switch

......................................................................................... 86

Figure 45: Settings: Two-button function - Switch

............................................................................... 87

Figure 46: Settings: Single-button function "switch" - switch

.............................................................. 87

Summary of Contents for BE-BZS86.01





































































































































































Search results

Summary of Contents for BE-BZS86.01

Reviews:

Related manuals for BE-BZS86.01

Brands by name

Popular brands

MDT Technologies BE-BZS86.01, Technical Manual

Search results

Summary of Contents for BE-BZS86.01

Reviews:

Related manuals for BE-BZS86.01

Brands by name

Popular brands