background image

Assembly Instructions 14 X 27 X 9 Party Tent Style

V2.0  14 X 27 Size 

INSTALLING THE UPRIGHT VERTICAL LEGS 

AT THIS STAGE, ESPECIALLY IN WINDY WEATHER 

CONDITIONS, THAT THE MOST CARE AND 

PRECAUTION MUST BE TAKEN. 

The frame and the roof cover are heavy to lift so 
adequate assistance will be required to guard against 
personal injury.  Only lift one side at a time:  Lift the first 
side and insert the Corner and Interior Uprights into the 
Frame Connectors.  Be certain to use the Corner Poles 
in the corner positions to secure the Roof Cover.  

Adding an Interior Upright and One Corner Pole 

To Roof Frame- One Side 

Both Corner Poles and Interior Pole Inserted 

If the end wall panels (#10) are to be used, attach these 
now to the rafter poles now before the tent is at its full 
height. 

Repeat the procedure with the remaining side panel.  At 
this point the tent is most vulnerable to injury & damage 
if it is windy.  If it is windy at all, use the guy ropes to 
stabilize the tent before the side panels are attached.  
There are holes in the feet plates through which they 
may be pegged to the ground. 

Part of the roof cover extends down each of the 4 
corners and attach to the poles by way of the “S” shaped 
hooks that locate in pre-drilled holes of the Corner Poles. 

To attach the sidewall panels (#11), start at the top and 
at one of the panel and use the bungee cords (#13) in 
the same way as you did to secure the roof. Along the 
eaves it is best to share the same eyelets: i.e. from the 
inside first pass the bungee elastic through the eyelet in 
the roof, then back inside through the eyelet in the wall 
panel, wrap around the pole and back over the toggle. 
Repeat with all attachment points along the eaves so 
that roof and the wall panels (where required) are 
secured to the frame, and where the vertical ends of the 
walls finish or join each other.  

BUNGEE CORDS

ATTACH WALL TO FRAME

COVER

BACK  WALL

BUNGEE CORDS

ATTACH WALL TO FRAME

SIDE WALL

Using Aligned Eyelets for Bungee Cords 

Using the Small Stakes (#17) provided, peg down the 
bottom edges of all sidewalls and end panels.  Drive all 
pegs in at an angle (ideally of 45

°

 or less to the 

horizontal) and in line with the seams.  

The guy ropes (#16) provided should be attached or tied 
to the frame only, ensuring that they are all pegged 

Summary of Contents for Rhino Shelter 14x14 Party Tent Style


































Reviews: