McQuay IM 689-2 Installation & Maintenance Data Download | Manualshive

Page: 5 / 52

background image

IM 689-2

5

NOTICE

This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with this instruction manual, may cause interference to radio communications.
It has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his or her own expense.

McQuay International

disclaims any liability resulting from any interference or for the correction thereof.

«
...
3
4
5
6
7
...
»

Summary of Contents for IM 689-2





















































Reviews:

No comments

Related manuals for IM 689-2

Brand: ICP DAS USA Pages: 8

Ubiquity QD2040b

Brand: TCS Pages: 8

Brand: Vantron Pages: 52

Mi Smart Home Kit

Brand: Xiaomi Pages: 4

Brand: Elpro Technologies Pages: 160

RT-RoIP2-Azetti

Brand: Solidtronic Pages: 8

Brand: Solidtronic Pages: 8

Brand: CSM Pages: 40

Brand: TEKTELIC Communications Pages: 20

Brand: Vantron Pages: 98

OfficeConnect 3CRWE53172

Brand: 3Com Pages: 124

OCG VOICE EXPANSION -

Brand: 3Com Pages: 177

TotalStorage NAS Gateway 500

Brand: IBM Pages: 471

Brand: T-Mobile Pages: 48

Brand: Avaya Pages: 162

Brand: IFM Electronic Pages: 22

Brand: Avaya Pages: 34

Brand: RTA Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands