manualshive.com logo in svg

McQuay IM 689-2, Installation & Maintenance Data

The McQuay IM 689-2 is a high-performance HVAC system packed with efficient features. Access the comprehensive Installation & Maintenance Data manual for free download at manualshive.com, offering step-by-step instructions and essential maintenance tips to ensure optimal functionality of this exceptional product.

Share
Download
background image

IM 689-2

29

BACdrop Setup Wizard User’s Guide

The BACdrop Setup Wizard is a suite of software tools that allow you to configure a BACdrop
gateway and commission a MicroTech network. It is a 32-bit program that runs on a PC equipped
with Windows 95 or Windows 98.

The BACdrop Setup Wizard helps you accomplish the following tasks:

•

 

Obtain a summary of pertinent system information

•

 

Configure the BACdrop gateway

•

 

Download software to the BACdrop gateway

•

 

Back up a BACdrop configuration file to the PC hard disk

•

 

Restore a BACdrop configuration file

•

 

Change gateway timing parameters

•

 

Perform a network diagnostic test through the gateway

•

 

Perform a network diagnostic test without the gateway

•

 

Read/write to MicroTech controllers via mapped BACnet objects

•

 

Configure MicroTech controller port speeds and port configurations

•

 

Log BACnet data packets

Each software tool is set up as a “wizard” that takes you step by step through each task, showing you
cabling diagrams and required communications components when needed.

System Requirements

Hardware—Minimum

•

 

486/33 MHz processor

•

 

500 kb space on the hard disk

•

 

8 Mb RAM

•

 

Serial port

•

 

Standard DB9 serial cable

Hardware—Recommended

•

 

10BaseT Ethernet adapter for PC

•

 

RS-232 to RS-485 converter (for example, from B&B Electronics: Model 485PTBR)

•

 

Power supply for RS-232 to RS-485 converter (for example, from B&B Electronics: 485PS2)

•

 

10BaseT null Ethernet cable or two standard Ethernet cables and an Ethernet hub

•

 

MicroTech PC Communications Cable Kit (McQuay part no. 057186802)

Software

•

 

Windows 95/98

•

 

Adobe Acrobat Reader 4.0 (required to display and print online Help and documentation)

Summary of Contents for IM 689-2





















































Reviews:

No comments

Related manuals for IM 689-2

FACTBIRD DUO Quick Start Manual preview
DUO
Brand: FACTBIRD Pages: 2
Abocom HA2500 Specification Sheet preview
HA2500
Brand: Abocom Pages: 2
Hirschmann OpEdge-8D User Manual preview
OpEdge-8D
Brand: Hirschmann Pages: 44
Danfoss KoolKey EKA 200 Installation Manual preview
KoolKey EKA 200
Brand: Danfoss Pages: 2
Toshiba XLTR-200 Instruction Manual preview
XLTR-200
Brand: Toshiba Pages: 99
MCK PBXgateway Quick Installation Manual preview
PBXgateway
Brand: MCK Pages: 18
Hewlett Packard Enterprise Aruba 9012 Installation Manual preview
Aruba 9012
Brand: Hewlett Packard Enterprise Pages: 26
Digicom VoiceGATE 8D5499 User Manual preview
VoiceGATE 8D5499
Brand: Digicom Pages: 29
Carel CloudGate-mini Wi-Fi Assembly Procedure preview
CloudGate-mini Wi-Fi
Brand: Carel Pages: 2
Technicolor MediaAccess TG789vn Setup And User Manual preview
MediaAccess TG789vn
Brand: Technicolor Pages: 128
EGi Millennium IP Series Manual preview
Millennium IP Series
Brand: EGi Pages: 16
Schlage ENGAGE GWE Installation Instructions & User Manual preview
ENGAGE GWE
Brand: Schlage Pages: 60
TelcoBridges Tmedia TMG800 Installation Manual preview
Tmedia TMG800
Brand: TelcoBridges Pages: 80
Avaya G150 Installation And Configuration Manual preview
G150
Brand: Avaya Pages: 254
2N Telekomunikace 2N BlueStar User Manual preview
2N BlueStar
Brand: 2N Telekomunikace Pages: 105
DBL Technology GoIP User Manual preview
GoIP
Brand: DBL Technology Pages: 63
3Com NBX 100 Administrator'S Manual preview
NBX 100
Brand: 3Com Pages: 496
Carrier Access Network Device Adit 3104 User Manual preview
Network Device Adit 3104
Brand: Carrier Access Pages: 74

Brands by name

Popular brands

Load more brands