manualshive.com logo in svg

McQuay IM 689-2, Installation & Maintenance Data

Share
Download
McQuay IM 689-2 Installation & Maintenance Data Download Page 33

IM 689-2

33

Version Information

The version numbers of the BACdrop gateway’s program and operating
system. If necessary, the BACdrop program can be upgraded by using the
BACdrop Setup Wizard’s Download tool.

System Error
Information

Displays any software loading errors that have occurred. For example, if
the PMF fails to load or the Ethernet controller driver fails to load, an
error message will appear.

Click the More button to view a list of the MicroTech controllers configured in the BACdrop
gateway, or click the Main Screen button to return to the Main screen.

If you click the More button, the BACdrop configuration file is read out of the gateway’s memory
and displayed. See Figure 14. Each MicroTech controller that has been entered into the configuration
file is shown with its MicroTech address, controller name or type, and Device instance number. You
can view the information, but you cannot change it with this tool.

Click the Main Screen button to close the System Information tool and return to the Main screen.

Figure 14. System Information Tool, BACdrop Configuration File Screen

Configure Controller List Tool

With the Configure Controller List tool, you define the MicroTech controllers that the BACdrop
gateway will translate data for. This definition includes the MicroTech network address, the standard
MicroTech controller type, and the BACnet Device object instance number. You can add, delete, or
modify any of this data. As an option, you can specify a MicroTech controller’s location, which
becomes the value of the BACnet Device object’s Location property.

Figure 15. Configure Controller List Tool, Main Screen

Summary of Contents for IM 689-2





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands