background image

mccue.com

4 BARRIER INSTALLATION INSTRUCTIONS

Questions?

  

Call McCue Customer Care at 800.800.8503

©2013 McCue Corporation, 13 Centennial Drive, Peabody, MA 01960, USA. MAR 2014

CartPark

 Architectural

1

2

4

5

10

11

11

5

15

14

10

12

Bill Of Materials

CARTPARK ARCHITECTURAL

ITEM #

QTY

DESCRIPTION

McCUE DRAWING 

OR PART #

1

1

Rear Left Vertical Post, 83.25” LONG

CCASFABVPRL

2

1

Rear Right Vertical Post, 83.25” LONG

CCASFABVPRR

3

2

Front Vertical Post, 83.25” LONG

CCASFABVPF

4

2

Lower Side Rail, Barrier Connector 135.4375” LONG

CCASFABLSR

5

2

Upper Side Rail, Guidance Rail Notched 135.4375” LONG

CCASFABUSR

6

1

Back Stop Bar, 95.1875” LONG

CCASFABBR

7

1

Top Rail Left, Horizontal Bar, 164.0” LONG

CCASFABTRL

8

1

Top Rail Right, Horizontal Bar, 164.0” LONG

CCASFABTRR

9

2

Crossbar Along Top, 96.875” LONG

CCPASFABCR

10

2

Roof Frame Assembly, 164” x 56.0” x 2.0” FRAME

CCPASFABRF

4

Roof Slope, 53.6875” LONG

CCPASFABRS

4

End Roof Slope with Tri-Glass Panel Mounting Holes

CCPASFABRSE

2

Top Ridge, with Weather Foam Tape, 164” LONG

CCPASFABRDG

2

Bottom Sill, 164” LONG

CCPASFABSILL

6

Roof Cross Member, with Double Sided Tape 52.75” LONG

CCASFABCM

ITEM #

QTY

DESCRIPTION

McCUE DRAWING 

OR PART #

11

6

Roof Panels, Acrylic Solid Sheet, 55.125” x 53.75” x .177”

CPAS-RFPNL

12

2

Retainer, Roof Drip Edge, 164.0” LONG

CCASFABRET

13

4

Plastic Barrier, HDPE, 70.25”  x  12.0” x 20.0”

CCPAS-BARRIER-XXX

14

2

Tri-Glass Panel, High Impact Acrylic, 100.875” x  28.3” 

x .236”

CCPAS-TRIPNL

15

2

Tri-Glass Panel Aluminum Support, 88.98”x.75”x.50”

CCPASFABTPNLSP

CCPAS HARDWARE

ITEM #

QTY

DESCRIPTION

130

¼-20  x  1.0” Torx Pan Head Screw, Taptite 2000, S/S

7

¼-20  x  1¾” Hex Washer Head Screw, S/S

7

¼-20 Serrated Washer Nut, S/S

14

¼-20x¾” Torx Pan Head, Self Tapping Screw, S/S

12

¼-20x  2.0” Pan Head Torx

20

Aluminum Shoulder Spacer ¼” ID  x  ⅜” LONG

4

#10-32  x  ⅜” Long #2 Drive, Thread Cutting Screw S/S

Summary of Contents for CartPark Architectural












Reviews: