Version 03/12
LED Mini Strobe Board
Item no. 59 14 68
Intended use
1.
The LED Mini Strobe Board is used to generate lighting effects on dancing floors, in party basements etc.. It is
approved only for connection to a standard mains socket. Do not use any other power supply. The product may
only be used indoors; never outdoors. Do not expose to moisture, under any circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
Delivery content
2.
LED Mini Strobe Board
•
Operating instructions
•
Safety instructions
3.
Read the operating instructions carefully and especially observe the safety information. If
you do not follow the safety instructions and information on proper handling in this manual,
we assume no liability for any resulting personal injury or damage to property. Such cases
will invalidate the warranty/guarantee.
Persons / Product
Do not look straight into the light source during operation. The bright light rays could temporarily impair your
•
eyesight. Apart from this, under certain circumstances epileptic fits can be triggered in persons sensitive to
such lights. This applies particularly to epileptics.
Objects that are illuminated must be at least 0.5 m from the light source of the device. Easily flammable
•
materials such as decorative fabrics must have at least a distance of 0.5 m from the device. Otherwise
there may be a fire hazard!
When installing or mounting, make sure cables are positioned so that they cannot be tripped over.
•
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous playing material
•
for children.
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
•
flammable gases, vapours and solvents.
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
•
accidental use. Safe operation can no longer be guaranteed if the product:
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
-
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the
•
product.
Miscellaneous
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
•
shop.
If you have questions which remain unanswered by these operating instructions, contact our technical
•
support service or other technical personnel.
Positioning / mounting
4.
The device must be mounted out of normal reach.
Positioning
Place the effect beamer onto an even, clean surface.
•
Mounting
Install the effect beamer using a mounting bracket on the ceiling, the wall or on a suitable crossbeam. When
•
installing it, make sure that the device cannot swing freely.
The bore diameter in the mounting bracket is 5 mm. To ensure safe mounting, select screws with a wider
•
screw head.
Secure the device with fastenings that are compatible with the fastening surface and suitable for carrying
•
the weight of the light effect device.
Secure the installation with an additional suitable safety restraint cable or net. The safety restraint cable or
•
net must be able of supporting the light effect device in the event of a fault in the main support system.
Set the desired angle of inclination and then tighten the bracket locking screws.
•
Operation
5.
The LED Mini Strobe Board can be controlled via the sound-to-light control or manually.
•
The operating mode is set with the on/off switch.
•
Switch position
Operating mode
O
Device off
I
Manual control
II
Sound-to-light control
The lightning frequency is set with the High / Low controller.
•
Manual control:
•
The LED Mini Strobe Board flashes permanently with the set lightning frequency.
-
Sound-to-light control:
•
The LED Mini Strobe Board flashes to the beat of the music.
-
Replacing the fuse
6.
Remove the fuse using a Phillips screwdriver.
•
Replace the fuse with a new one of the same type.
•
Screw the new fuse in tightly.
•
Cleaning
7.
The outside of the light effect should only be cleaned with a soft, dry cloth or brush.
•
Never use aggressive cleaning agents or chemical solutions as these may damage the surface of the
•
housing.
Disposal
8.
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Technical data
9.
Operating voltage:
220 – 240 V/AC, 50 Hz
Power consumption:
10 W
Lightning frequency:
min. 3/s , max. 11/s
Light source:
261 white LEDs
Operating temperature:
-10 to +45 °C
Operating humidity:
20 – 95 %
Storage temperature:
-20 to +55 °C
Storage humidity:
10 – 95 %
LED beam angle:
120 º
LED Ø:
4.8 mm
Cable length:
1 m
Dimensions (W x H x D): 250 x 90 x 79 mm
Weight:
885 g
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2012 by Conrad Electronic SE.
V2_0312_02-JU
